Search the Community
Showing results for tags 'Matte Varnish'.
Found 3 results
Start with three Goblins, painted (poorly) with MSP. (Reaper bones Goblins 20024) Then give two of them two coats each of Liquitex Gloss Varnish - Artist Acrylic 6208, with 3 hours between each coat. Shiny! They're dry, but don't look like it. The spearman is the Control (unvarnished). Next, the Matte sealers. The Spearman is still the control. The archer was given a coat of Liquitex Matte Varnish - Artist Acrylic 5216. The Liquitex Matte goes on just like the Liquitex Gloss, its milky and tranlucent, and prone to bubbling. I have to give it a good coating, then go back over it with the brush and basically pull a bunch off where it's pooled or turned into foamy wierdness. The Mace guy was given a coat of Testors Dullcote Lacquer 1160. The Testors goes on clear, and maybe a little thicker, but it starts to dry out and/or turn matte fairly quickly - you can see it starting to happen by the time you finish one mini. It's really easy to just slap on a coat and not worry too much. Three hours after the first coat of matte, the Liquitex looks kind of greasy. Still shiny, and thick. The Testors looks waxy. Like it's not wet, but there's a layer of something mostly translucent that you can see, dulling everything down. Both are still too shiny, so a second coat of matte is applied. Three hours later: Pretty darn similar. Both still waxy, and shinier than I'd like. Compare to our friend the Control: So a third coat of matte must be applied. This time I remembered to take pictures of what the Liquitex is like! slathered on: and with the excess brushed off: That's still wet, it's just really hard to get the stuff on the mini in a reasonable fashion, and I'm trying to avoid the nebulous 'over-brushing' which can cause fogging, or so the products tell me. Three hours later, here's coat number three: The testors looks shinier in the pic, but they're both about the same in person. Speaking of looks, see how terrible the sealed ones look next to control: What am I doing? I'm ruining them. One thing politics has taught me is to never admit you're wrong. Stay the course. Keep on keepin' on. So I put on a fourth coat. It's not getting any better. Furthermore, I don't really see a difference between the two matte sealers, all I can focus on his how much better the unsealed one looks, and how bad the other two do. Look at the bases! Same photo but zoom/crop: Unsealed (left), then Testors (middle), then Liquitex (right) My sloppy drybrushing, mostly undone by liquid evil. So what I was originally trying to find out was the difference between the matte sealers. Why? Because it's too cold/wet outside to use my spraycans. I originally used a couple coats of Krylon UV-Resistant Clear Acrylic Coating, then one coat of Testors Spray Lacquer Clear Coat (which is actually Dullcote, but just labeled incomprehensibly). This combo worked GREAT. But in winter (and for some reason, I find myself painting more when I'm trapped inside for months at a time) the sprays aren't so good, hence the brush-on sealers. I noticed my brush-on minis were not as nice as the spray ones. Maybe it's liquitex's fault, maybe their matte isn't good, etc. When I found out Testors made a brush-on dullcote, I had to give it a try. And I think what I've found out is that Liquitex doesn't suck, I do. I think my problem is the initial coat. Or all the coats. Too thick, too much. The reason it looks like it's covered in waxy stuff is because it actually is covered in waxy stuff. So what to do? I noticed the Testors bottle says to "ONLY" use Testors brand thinner to thin for brushing. Am I supposed to thin this stuff? How much? It just says "apply generous coats"! How thin? Doesn't thinning it mean it's not fully sealed? Argh! Also, I don't have gloss Testors. My only gloss is Liquitex, and it's VASTLY different (see: milky foaming bubble mayhem). Can I use the "Lacquer Thinner & Brush Cleaner" on the Liquitex? It says not to thin with water. Does that mean don't thin it, or do thin it, but with some thing else? It's "varnish" is that the same as Lacquer? Or are they different things? If so, what can I use to thin the Gloss Varnish, if anything? Would thinning it make things better? It's a "Acrylic Polymer Emulsion" but I don't know what the Testors is actually made of. It's too late for these poor mistreated goblins, but hopefully I can figure something else out. Maybe I just need to be (far) more careful, or maybe there's a different product I can use, but I've got a lot of bones, and very little Summer.
Anything I should know before coating my painted bones figures to protect them? I'm using liquitex matte varnish - as a brush on, too humid to spray here. I've not had any problems with it before just want to make sure there's not anything special I need to know about bonesium tm before I finish this figure.
So I've been playing around with what varnish's I like over the last few months and finally settled on Vallejo Matte over a Liquitex Gloss. The mini ends up very well protected and the Vallejo is an amazing matte, at first. The problem comes with handling. The matte eventually turns satin. I can easily duplicate this effect by simply rubbing hard over an area a few times after I've let the Matte dry. Anyone familiar with Vallejo that could help me figure this out?