Jump to content


Photo

Drool Tutorial


  • Please log in to reply
6 replies to this topic

#1 Jabberwocky

Jabberwocky

    Godlike

  • Members
  • 3073 posts

Posted 12 September 2007 - 05:28 PM

I whipped this together after some folks asked how I did the drool on my eyebeast.

Step 1—Gather the tools

The things needed for the drool I make are pretty simple. You need an “armature” for the drool to hang off of. Here I have used 4 pound test fishing line, but anything that is thin, fairly flexible, and clear will do. For the drool itself, I used two types of glue. I like the Gel Control Loctite for the base of the drool, then regular Loctite superglue for building it up. Again, anything that dries clear would work well, and I think PVA glue would suffice. Finally, gloss varnish will be the last item you will need.

Posted Image

Step 2—The skeleton and first layer

First, I cut the fishing line to length. I cut it a bit longer than what I am going to need. This allows for two things; I can hang the line vertically on a pen or pencil with some putty or tack (as seen here) and I have a little room for error to get the drool the right length. The pen and tack just make it easier to get that “blob” at then end of the drool due to water tension.

Posted Image

Next I add the gel type superglue. I prefer this as my initial layer because I can “mold” it a bit with a toothpick to pull the glue down along the thread and get it in a position that I prefer. I place the blob of glue up near the tack and then use a toothpick or the nozzle of the superglue to tease the glue down the line until the majority of it is at the tip. This gives you the nice “blob” from water tension seen with real life drool. The regular superglue especially (and to a lesser degree PVA) is very fluid and since you are trying to get it to stick to a very thin piece of fishing line, and in my experience was a pain in the bahooky to try and control. The glue just dripped off the end of the line, leaving only a very small portion still coating the tip. Allow this to dry.

Posted Image
Posted Image

Here is a close up of Step 2:
Posted Image


Step 3—Thickening the spit

At this point, I use something a bit more liquid. You could add more gel if you want, but I prefer the thinner stuff now because it tends to layer out more smoothly along the line. Again, take a bit of superglue/PVA glue and place it up near the tack and allow it to run down the line. Let the glue dry and then add subsequent layers until you are satisfied with the result. I kept my drool clear, but between steps 2 and 3 is where I would add any coloration, such as a green for bioacid or blue for a water effect.

Posted Image

When the glue goes on initially, it is nice and shiney. As it dries, it tends to go a bit more matte.

Posted Image

Step 4—Gloss the drool

The last step is to varnish the drool to get that life like effect. I simply layered on some undiluted gloss varnish to give it that highly reflective sheen as well as add a bit more volume to the spit.
Posted Image

Once you have the drool completed, cut to length and superglue in place as I did on Reaper's Eyebeast.
Posted Image

I hope you have found this useful!

A piece of art is never finished. It is simply abandoned. --Whizard Hlavaz

 

My Jabberbloggy: http://jabberwockymi...s.blogspot.com/


#2 Versutus Vulpes

Versutus Vulpes

    Godlike

  • Members
  • 1735 posts

Posted 12 September 2007 - 05:42 PM

Definately!

Never would have though to use the fishing line...

Thanks for this - it's greatly appreciated.
It's not enough to bash in heads - you've got to bash in minds... ~ Captain Hammer ~

#3 Joe Kutz

Joe Kutz

    Godlike

  • Members
  • 1364 posts

Posted 12 September 2007 - 05:56 PM

You can also do webbed saliva by doing most of the same stuff but doing it with the armature sitting flat on something like aluminum foil or was paper.

#4 tanker22

tanker22

    Master

  • Members
  • PipPipPipPipPip
  • 820 posts

Posted 12 September 2007 - 06:29 PM

Thanks, thats areally cool idea. I would of never though fishing line either. Wanted to try and do blood dripping of the ax of the viking I'm working on in a WIP. May have to add that later though, need supplies first.

Thanks again JW
"Wars are not won by the most competent army, they are won by the least incompetent army." -Ralph Peters, Red Army


<a href="http://www.coolminiornot.com/artist/Tanker" target="_blank">http://www.coolminiornot.com/artist/Tanker</a>


Ebay Auctions

#5 Wren

Wren

    Godlike

  • Artists
  • 2185 posts

Posted 12 September 2007 - 10:13 PM

Very nice tutorial, it's got a clear explanation and great up-close photos.

#6 TaleSpinner

TaleSpinner

    Sculptor of Stories

  • Bones Supporter
  • 5155 posts

Posted 13 September 2007 - 11:37 AM

You should send this to Kit as a Craft item.

TS
Some tales are better left for the light of day.

My Website: www.talespinnerminis.com

#7 aquila

aquila

    Mostly Harmless

  • Members
  • 25 posts

Posted 14 September 2007 - 04:02 PM

that's a cool idea. thanks for the tip
Posted Image




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users