Jump to content
Couvs

01604 Eli Quicknight mold line

Recommended Posts

8 minutes ago, Gadgetman! said:

But for us, who are working with pewter...  

 

Ahh, but with Bones, ....

  • Like 1

Share this post


Link to post
Share on other sites

If all else fails and you're unable to shave/file down the high side enough, you could always try building up the low side with a bit of green stuff (or your favourite alternative putty)...

 

Good luck,

 

Kang

Share this post


Link to post
Share on other sites
23 hours ago, Cyradis said:

I may have just been given a crazy scheme to pull out my graver and try to engrave patterns onto figures.... uh oh. Thanks Wren for reminding me of cool jeweler tools. 

 

I hope you show us what you come up with!

  • Like 1

Share this post


Link to post
Share on other sites
5 hours ago, Wren said:

 

I hope you show us what you come up with!

 

You know it! :) 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Grayfax
      My brother was cutting up cedar limbs to use for a project for his wife.  I figured I might as well grab a few just in case I might could turn them into bases or platforms for miniatures.  I have several sizes and several heights, but when I started looking I was not finding much on integrating something like this into a base.  Lots of things for already prepared woods, but not many ideas on fresher wood.  Now, most of these limbs were dropped from trees, so, not exactly full of sap:

      I am thinking I would need sealer but wasn't sure how that would interact when trying to get a miniature to adhere, or should I strictly use the taller ones as a plinth of some kind that the completed miniature sits on?
      Thoughts? Ideas? Practical experience?
      Also need to find the best way to handle the bark (leave it, clear it, etc.).
    • By Loim
      So, apologies if this has been brought up before. While prepping Gandorf for paint I have found a good viable alternative to sanding sticks and needles. Sand paper, or emery cloth. I've been using very small squares of it. About 180 grit. Rub it across the mold line against the sharpest edge and it slices it right off. It it also easier, in my opinion, to get it into the very fine areas, since it can be shaped or folded to match the contours. Hope this helps some of you out. I know it has helped decrease my Bones prep time. 
    • By revloc8
      So I broke down and got back into the hobby after 15+ years (life was so much easier in high school), and got Bones 1, and a bunch of other figs on KS. I'm really glad I decided to get back into painting cuz it's just so much fun. However, I've gotta say that mold lines are driving me crazy. I don't recall that being an issue for me years ago, so maybe I've become more picky? I dunno.
       
      So I do my initial cleaning with a hobby knife, and found that there were some knooks and crannies that I just couldnt do with my knife. So I got some needle files, but I think the grit must be too high cuz I feel like they just scrape my minis terribly. So I've decided to buy some sanding needles to see if they are better. These are the ones I'm looking at:
      http://www.ebay.com/itm/Albion-Alloys-Coarse-150-Grit-Sanding-Needles-8-344-/331106300338?pt=UK_ToysGames_ModelKits_ModelKits_JN&hash=item4d177931b2
       
      I've got two questions: how low of grit should I be using? 150? 240? 320?
       
      Secondly, how long should a set of sanding needles last? I've got several hundred minis to clean and paint, and I live in South Korea, so its not like I can just go down to the local craft store for more. Will 8 be enough? Or should I get two packs?
       
      Thanks in advance for helping, and thanks to everyone for all the awesome guides, advice, and other goodies you've contributed on these forums. There's so much good stuff, it's a little overwhleming :)
       
    • By Iron Knight
      Howdy,
       
      I've met with some pretty bad first results on my bones minis. I think where I am going wrong is base coating. Undiluted I am having to do several base coats and it ends up killing the model's detail (and it also might be making the mini's really shiny...). I would really like to find a reliable method to get the model covered so I can paint like 'normal' with out all the beading. Could anyone recommend a paint line that work in a pass or two to base coat that's worked for you? Gray, black and white are my usual colors but any colors would be great too.
  • Who's Online   13 Members, 0 Anonymous, 0 Guests (See full list)

×