Recently Browsing 0 members
No registered users viewing this page.
This year the minis I manage to paint will all count towards the resolutionary challenge. As per the resolutionary painting challenge guidelines, I will post them here, and link in my post in the challenge thread.
Finished a second squad of the Mars Attacks! Martian Grunts.
Some of the helmets are a bit wonky in the picture, as they are not glued down yet. I use thinned PVA for that, because it sets transparent and can be scraped off with ease if the need arises.
Mars Attacks! the miniatures game
PVC (that is rather similar to the more rigid bonesium from Bones 2 KS)
25mm integral bases.
The rocket shuddered as the flare behind, even at distance, buffeted the small craft to and fro. Dr. Bedlam glanced around the cockpit; though rivets shivered and struts groaned, the vessel still seemed to hold together. Stretching out a tanned, muscular arm, he drew back the throttle, decreasing fuel flow to the overworked engines; in response, the rocket slowed slightly in its passage through the luminiferous ether. He'd made it!
But Dr. Bedlam allowed himself no self-congratulations; the job was not yet done. His tanned, muscular chest still ached, and his tanned, muscular back still bore the marks of the whips of the Voodoo Virgins of the Vengeance Vector! He had allowed himself to be cozened once, and the inhabitants of the planet Gorkulon had paid with their lives. He would not be fooled again! Luck had been with him once, but even he dared not count on such when the fate of the Galaxy was at stake! The Voodoo Virgins would stop at nothing to dominate the Sagittarius Arm, and Dr. Bedlam knew that although the Galaxy Bureau of Investigation was clever and mighty, the wiles of the Voodoo Queen, Squeema, and her hypnotic powers of seduction would catch them unawares.
Unless he, Dr. Bedlam, were to get there first... and warn them!
Suddenly, a flicker of light on the Omniscioscope caught Dr. Bedlam's attention. "Eh?" he said to himself. "There's no way they could have caught up yet -- unless..."
A blip of light appeared on the hemispherical screen. Before his tanned, muscular eyes, it seemed to grow... and grow ... and GROW...
TO BE CONTINUED!
My first thoughts on painting the minis:
If you start masspainting your Mars Attacks and want do it fast.
I have for example 40 human soldiers to paint.
I think it is possible with this method to have them all completed in 4-8 hours, eventuall even with highlights.
Preparing the minis:
0. if possible train painting on a few metal minis, not necessary, but helpful.
1. wash the minis. Use Soapy water, I use normally a fat solvent spray.
2. use a primer, I would use white primer, but black or grey is ok, too
Don't use to much, you should be still able to see the details.
With a double-sided tape and a card board, you can prime many minis together.
3. I try to get all paints together I want to use on the minis before I start to paint, so I do not need to search after it.
If you need later to remove paint and you can get 'Simple Green' it is normally perfect to remove paint from plastic minis (test it first on one mini!!!)
Description for human soldiers, but it works also on every martian grunt, marines and other uniformed group.
1. Do ten minis in a row or more, but for me are more than ten minis at the same time not good.
2. put first the base coat of colors on the minis, but only one color on every mini after another.
As example for the soldiers:
2.1 uniform mini 1, uniform mini 2, .... uniform mini 10
2.2 webbing mini 1, webbing mini 2, .... webbing mini 10
2.3 gloves, gloves, gloves
2.x and so on.
3. same with the camouflage always one paint of the camouflage on every mini's uniform, before you start with the next Camouflage paint
4. ignore or do the highlights, if you want
Use of Army Painters Quickshade (QS)
1. get white spirit and an old brush before you start!
2. put army painter quickshade on 10 minis with a old brush on every mini. Don't dip!
3. start over in the same order as you put QS on the minis, and remove QS from places where is to much QS on the minis.
4. do step 2-3 until all have QS on them...
5. clean the brush immediately with white spirit!!!
6. QS must try 24 hours!!! Even if you can touch it, don't proceed with the mini!
7. eventually think about highlights and error corrections, before you put matte varnish on the mini.
1. Eventually think about which colors you are using during these steps on the heroes of greenville. Prepare them, too.
If you use black while doing masspainting and want the jacked of one mini black, do this or these minis, too!!!
2. if you want to remove errors before putting QS on them , do it after all minis of the same type are painted
3. Ignore small painting errors, you can remove visible ones later before you put QS on them.
Small errors are sometimes not visible after quickshading and if they are still visible, you can remove them after the QS easily.
Here you can get a tutorial for woodland MARPAT for the soldiers
the base coat looks little bright, I think it is the camera, I don't think the color is really sooo yellow!
I had already some thoughts about Martian Minis:
(standard Grunts, including freeze ray and unit commander)
1. white primer
2. complete body: Vallejo 72.024 Turquoise
3. boots and gloves: green (unit commander: Vallejo 72.007 Gold Yellow)
(not sure which vallejo color I will use, eventually I must mix greens or buy a new one)
4. Brain: Vallejo 72148 Heavy Warm Grey, eventually later Reaper MSP Brains Pink as highlight, a wash (sepia?) as last step.
5. face: vallejo 72,035 dead flesh is my favorite in the moment
6. Option 1: weapon and some body part: black, highlight with Vallejo 72.050 Cold Grey
Option 1: Or I use Black, VMC gun metal grey and silver as highlights
7. Gas Bottle: Vallejo 72.012 Scarlet Red
8. few smaller details...
I think the martians are very fast to paint.
!!! Do eventually the head and face in step 4.-5. on every martian mini at once.
I'm waiting for the MA minis in the moment, too! :-(
Who's Online 21 Members, 0 Anonymous, 0 Guests (See full list)