Jump to content

Search the Community

Showing results for tags 'loot studios'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Reaper Discussion
    • News
    • Reaper General & Faq's
    • Reaper's Product Lines
    • ReaperCon
    • Reaper Virtual Expo
  • Reaper Social
    • Exchanges and Contests
    • Birthdays!
    • Socializing
  • Painting
    • Show Off: Painting
    • Works in Progress: Painting
    • Tips & Advice: Painting
    • Shutterbug
    • Speed / Army / Tabletop Techniques
  • Sculpting, Conversion, and Terrain
    • Show off: Sculpts, Conversion, Terrain.
    • Works in Progress: Sculpts, Conversion, Terrain.
    • Tips and Advice: Sculpting
    • Tips and Advice: Conversion
    • Tips and Advice: Terrain
    • Tips and Advice: 3-D printing
    • Conversions, Presentation, and Terrain
  • General Discussion
    • General Fantasy
    • General Sci-Fi
    • General Modern / Historical
    • Kickstarter
    • Off-Topic Rampancy
  • The Sandbox
    • The Gathering
    • The Playing
    • Fiction, Poetry, and Other Abuses
  • Reaper Games
    • Dungeon Dwellers RPG
    • CAV
    • Warlord

Calendars

  • Reaper Events
  • Forum Contest

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 2 results

  1. Of the many busts I’ve printed/purchased lately, this one won out on the priority list. Basecoats and metallics are a mix of acrylics (Reaper and Vallejo) and then a ton of layered oils with some subsequent acrylic highlights again. Painted the eyes very faintly and then “washed them out” to give them that milky look but I feel I went too far as the iris/pupils are pretty much gone. Otherwise, I’m quite happy with him other than the missed support nubs inside his “crown” that will taunt me forever. Thanks for looking.
  2. This year's Christmas present to myself was a Sonic Mini 4k printer. I've done a few runs now and promised a pic of a painted mini at some point. Gardain here was a bit of a failure as it turns out there were a few problems with the pre-supports. Still, he's 99% ok which means he's good enough to use as an example, but also that I don't care enough to paint to a high standard. So with that in mind, he was painted with a thin layer of primer through the airbrush, a slightly thinned basecoat, and then a few washes. I.e. the point is to show off how much detail the printer can do, how visible the layer lines are, etc, not how well I can (or can't) paint. He is a 32mm scale dwarf, which means he is a little taller than a Reaper dwarf, but not quite as tall as a Reaper human. The very bottom of this gauntlet pancaked, but you can only really see it if he is upside down. Yup, that's a hair support. The presupport was at too low of an angle so it bonded to the figure. Btw, those eyes are tiny. His right eye is really bad because the arm blocks coming in from below, the sculpted bushy eyebrow makes any high angle impossible, and he has a big nose. Jab straight in and hit where you aim! In fact, they are so small that I can't even tell I painted them at arm's length. If you skipped them to get him on the table no one would notice. And there you have it, my first [painted] 3D print.
×
×
  • Create New...