Search the Community
Showing results for tags 'Board'.
Found 4 results
Hi Guys, Just thought i'd share this project with you. i've been working on it for a few weeks now. I run a weekly gaming session using a home brew system that we've been working on for about 20 years, but this post isn't about that - though if you're curious please send me a message i'd love to chat about it. First as is the tradition - the completed board in all it's glory. On the surface, it's nothing unusual, however hidden inside each tile is a small rare earth Magnet. I'm also placing magnets on the bottom of the miniature bases. This gives the miniature a very nice pull towards the board and keeps everything in it's proper square. I'm also going to produce walls, columns and doors each with magnets in to allow me to customize the terrain. I chose a typical dungeon style flooring as it's easier to get a good grid pattern going. Though given that there's magnets in the board, i could easily design tiles to sit on top of the board with other terrain types. I'm trying to think of a way to get an outdoor setting and still keep the grid going. and now to the construction. I began with a thing piece of panel wood only about 6mm thick as the base for the board and placed little rubber stoppers on the bottom for feet (i didn't think to take a picture of that as it's not very exciting.) This board is going to to be the base for the board. On top of them I placed 3d printed tiles. There's only about eight different designs of tile, but with placement and paint they come up looking very distinct. It took about four hours for my little Anycubic Filament Printer to print the tiles (and I had alot of help from some friends and the local 3d printer store) Each tile is 4x4 squares with each square bring 30mm. Each Tile took about 5 hours to print. On the underside of the tile is small circular holes about 10mm wide and 2mm deep just big enough for the magnet - though with the print tolerances of the printer i did have to use my dremel to widen the gap so that the magnet could fit comfortably.In the end, i applied superglue to make sure that the magnet wasn't going anywhere. I also had to mark the magnets to make sure that they were all facing the same way. (I'm also thinking about adding a few magnets of the opposite polarity into the base of a Beholder Miniature to see if i can get it float, but that might be just a pipe dream) Once the tiles were finished it was simply a matter of spraying the board black as a printer and placing a thick coat of grey paint. I simply used the Acrylic paint from the local art store rather than my Citadel paints. This simply acted as the base coat and then i simply built it up in layers with dry brushing lighter shades on to the board to give it depth. Once this was done I simply mixed in some blue with my paint added a bunch of water to water it down and made a thin wash to bring out the details. I'd need to come back in and add in some of the features, such as the trap door and drains. I also sprinkled some Skulls, broken weapons and shields for good measure onto the board. Once the painting was done, I used a thick mud agent, I can't remember the brand from my local gaming store and then covered the whole thing in flock and sand to give it a grimy, slimy feel. Unfortunately, my poor AnyCubic didn't survive the process (May it rest in peace) So this gave me the opportunity to buy a Resin Printer - A Creality LD002S. The Goblin Wolf Riders were my first print. Actually really impressed with how they came out. Other than the clean up, It wasn't too difficult. I used a water soluble Resin to make things easier to keep neat. I was pleasantly surprised at how easy the whole process was - It was much much easier than dealing with Filament printers. Once the board was finished, I then cheated and had the board framed at my local picture framing store (the only thing i didn't do myself.) Once I got the board back, I thought it looked a little plain So i decided to glam it up - Also was a good excuse to stop printing Mini's on my 3d Printer So i thought i'd print a Celtic pattern around the edges. I knew that i wouldn't be able to print them in one solid peice (Resin printers only downside is a small print bed) So i decided to make little tiles. I designed these tiles myself, grabbing the celtic design online and then simply just adding them into 3d builder and setting a thickness to them. A quick coat of gold Spray paint and they came up looking real shiny.. Too shiny.. I added a wash over the gold to attempt to dull them, the pictures don't really do it much justice, but on the board it breaks up the gold really nicely. By this stage i was feeling pretty clever with myself, so i thought i'd added another feature, Gemstones in the frame. this proved easier than I thought, I quickly found an STL file for the gemstone and then it was simply a matter of giving them a coat of Citadel's technical range - Waystone Green, Soulstone Blue & Spiritstone Red. The finished photo really doesn't do justice to the how the gemstones came out. and there you have it. About 6 weeks to complete (most of this time was waiting for my anycubic 3d printer to finish printing the tiles) Let me know what you think! I can provide the STL Files for the tiles if anyone out there is interesting in having a go at making one for themselves We're shutdown right now because of the Corona Virus, so no RPG for us for a while, but i can't wait to get back into it with our shiny new board. Cheers, Chris
It's been procrastinated for way too long. These are the robot miniatures from my Robo Rally board game. Finally gotten a semi decent paint job. Poor Twitch has been lost under a couch somewhere, and has been replaced by a 3d printed version of Borderlands' Claptrap. He'll get a greenstuffed arrow-like base to match the others when I eventually get to it. But at least they have some colour! :)
http://rpg.drivethrustuff.com/product_info.php?products_id=83216&affiliate_id=294988 This is excellent stuff. A mate blogs on the subject here: http://sirrob01.wordpress.com/2013/06/15/papercraft-build-inked-adventures-dungeon-cut-up-basic/ He's become something of an expert on all aspects of printable terrain, miniatures, etc., so do yourself a favour and have a look.