Jump to content

Recommended Posts

post-11942-0-71842200-1372200234_thumb.jpgpost-11942-0-58088400-1372200154_thumb.jpgpost-11942-0-12775300-1372200064_thumb.jpgpost-11942-0-60725500-1372199987_thumb.jpgpost-11942-0-48113100-1372199913_thumb.jpgpost-11942-0-15117100-1372199795_thumb.jpg

 

Fortune Teller tent & vignette. This is the (1st) of 7 vignette pieces that will make up the traveling Gypsy market. It is complete except for the base edge ground cover work & the final seal spray of the whole vignette piece...The piece is a (4"x6") vignette built on ceiling tile.

  • Like 4
Link to post
Share on other sites
  • Replies 6
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Lovely as always! Your gaming groups if Very Lucky!

 

What spray sealer are you using for your terrain?

Hi Tom. I use either (Model Master Lusterless Flat) or (Testors Dullcote Flat # 1260)...both work exactly the same with the same basic results.

  • Like 1
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By lexomatic
      I few years ago I emptied a can of spray foam for some hills. I decided to hack up one to see if I could do some scatter that was more rock  pile than grassy hill like I've previously done (insert link to foam experiments thread).
       
      About a month ago I hacked the foam hill, and last night I glued it to a dead DVD as a base and clamped it.

      This is what it looks like now.

      I'm going to let it dry a bit more then give it some goop, then a modge seal. Then drybrush, and maybe some flock.
    • By Inarah
      Fun little piece. I attempted to paint it in the style of Costa Rican coffee wagons.  It was a real challenge, given the irregularities of the wheel surface.  I wish it had a donkey, goat or ox to pull it.  
       

       
      It will stand upright by itself on some surfaces, but I stuck a block under it to stabilize during photography. 
       
    • By Inarah
      This could be more exciting, but it's not.  I chose this as a test piece before I tackle Dragons Don't Share II.  Nice piece, it came together in a jiffy. I'm trying to copy the local limestone, and didn't quite get there with this, but it's a starting point. 
       

       
    • By Inarah
      Venomous Flowers by PrintYourMonsters.  These are 3d resin prints.  Of course, they might also be only harmless spring flowers on some sci-fi world. 
       

       
      The smallest one is a bit over 1" across, the largest is taller than a humanoid figure.  Overall I've been very happy with the Plants and Rocks files. 
       
    • By Darcstaar
      Taking a hiatus on the Mocking Beast.
      Trying to gain some victory in numbers on my Bonesium Horde.  I have completed the beetle swarms, spider swarms, and skeletons without WIP. 
       
      I’m going to do the goblins now.  I plan two batches: one yellow/ochre, and the other tangerine.  Some nice “non-Greenskins.”
       

       
      Several of these required boiling.  Some are still leaning.  The spears are straighter.  One of these was the beneficiary of a weapon swap.  I had given Danar, Male Assassin 77030 his shield for a spiked shield.  In return, we have a dual wielding goblin!
  • Who's Online   15 Members, 2 Anonymous, 31 Guests (See full list)

×
×
  • Create New...