Jump to content

Hordes of Things, 15mm Jabberwocky, Daughter's Christmas Gift


Recommended Posts

As I stated in the WIP & Show Off of the Jabberwocky for my daughter's birthday some time ago, she's a nutter for all things Alice, especially the Jabberwocky.


So, for Christmas, I am putting together and painting the one from Hordes of Things.  It's 15mm scale so it's smaller than our normal game play minis but it's really for her shelf at home.


Example Image from Hordes of Things:




At first I was pleased that the company left such nice pinning stems from the pieces.  I soon learned that they don't hold up ... AT ALL.  Grumble.


Here he is in the package:  Those "pins" are nearly a half inch long for the arms and wings.




I cleaned it all up and filed what little mold lines there are.


Here's a shot of the wing:





The integral base was round.  Nice and smooth but round.


So, I lopped off segments of it to make "right" angles so I could blend it in to the base with some cobblestones on it using a Happy Seppuku stamp.




Here's the stamp applied to one of my tile bases. with a cut away for the jabber's base:




And here it is with the Jabberwocky sitting in place:




I might file/cut some cobblestone lines into the base to break it up but with the straight lines and some paint, it's not as noticeable as the round.


You can see I added the right arm.  I had to pin it after the integral pin snapped.


I used a green stuff ring to better fill the connection to the head (not shown but done).


I added taller cobblestones to the existing ones once the first stamp was somewhat less pliable.  I'll file them down some more so they just slightly raised.  Irregularities improve perception in my opinion.


Tomorrow I will clean up the edges of the cobblestone with some more around the outside edge using a brick edging stamp from HS or just trim the edges straight.


More photos tomorrow after Paint Day.


  • Like 12
Link to comment
Share on other sites

  • Replies 12
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Got back to this at Paint Day.  Too many crafted things for Christmas plus the wedding left some things unfinished.


Basecoats added:




Also did some selective washing after photos were taken.


Will post more later as well as pics from other's paint day pieces.

  • Like 6
Link to comment
Share on other sites

Looking good, I really like that base!


It's the Happy Seppuku cobblestone stamp.  I added some pieces on top of the cobblestone stamped parts to have some raised pieces for more dimension.


I lined in some black to make the cobbles standout for detailing later. I'll try to remember to take a picture of that phase.


Next, I'll be lining the deeper sections of the scales with a dark purple for the belly and the hide.  It'll get the the colors like I used in the Warheads: Medieval Tales version:


  • Like 4
Link to comment
Share on other sites

Took three days off to travel with my wife to a conference 3 hours away in Saratoga Springs, NY.


So, I got out a couple of projects to bring with me since I get to hang out while she's at the conference.


So, we return to the Jabberwocky for my daughter.


I glazed one side of him with Scale Color's Amethyst which is a nice purple with some sheen to it and glossy finish.  I painted the underside of one wing and then washed the green scales with it and the belly skin/scale area.


I am digging the color overlaid on the green and the glazing on the wing.


Here's a quick pic of it:




Will take better pics later.

  • Like 6
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Similar Content

    • By Thrym
      Hordes of Things


      Roving the Streets
      ~ Daughter's Christmas Gift ~
      Okay, so I started painting this shortly after I gave it to my daughter for Christmas ... 2014.   You can read the WIP.  He languished in a box, in my kit, on and off for the last two years.

      A while back I pulled him out and applied a new paint, Scale 75 Amethyst Alchemy, as a wash over his already green and purple body to give him a metallic look and feel.

      And now in my recent kick to clear some Shelf of shame Space, I have FINISHED this Jabberwocky.  Whew.  Just in time to "re-gift" it to her.
      Here's what went into this bad boy...

      Body :: Vallejo Yellow Green Face, Underbelly, Spine and Wings :: Reaper Witchcraft Purple Claws and Eyes :: Vallejo Pancer Aces Stencil Washes & Glazing:
      Purple :: DecoArt's Americana Gloss Enamel Dioxazine Purple Metallic :: Scale 75 Amethyst Alchemy Highlights ::
      Claws, Wing Spines, and Horns :: Scale 75 Black Metal Horns, Wing Spikes, and Tail Spike :: Vallejo Blue Violet Eyes :: Reaper Sun Yellow blended to Reaper Rach Red Flagstones:
      Reaper Ruddy Brown Vallejo Yellow Green Reaper Rattlesnake Leather (Promo Color) Highlights :: Reaper Rainy Grey Crevices :: Reaper Grey Liner Base:
      Happy Seppuku Flagstone Stamp Green Stuff Architectural Tile Sample All in all, he was an interesting build and paint.  The only thing I don't care for on this mini was the sculptor's treatment of the claws.  They were kind of armor-like and didn't quite fit in with the overall esthetic of the mini.

      Here's "Wocky" ...




      Added to Thrym's General Show Off List
    • By Pingo
      Happy birthday to you! :bday:
      ETA: Mods, please merge my thread with Corporea's.
    • By aku-chan
      From my Through the Looking Glass WIP thread I bring you Steampunk Alice:-

      Decent photography continues to elude me
      Had super elaborate basing plans for this one, but they fell apart mainly because I was too cheap to buy a tiny mirror or frame (they probably would've fallen apart any ways, but I will never know now). So I fell back on my usual cork based ruins, though hopefully the chessboard pattern gives off enough Wonderland vibes.
      On the plus side, I'm really pleased with her hair and I didn't do too terrible a job painting her apron white.
      As always, any comments or criticisms are most appreciated.
    • By chaosscorpion
      At the suggestion of Adrift and Metalchaos I present you with the WIP of transforming my Game Room.  The costs of the endeavor were a Christmas present from my wife.  My wife was very understanding during the process and there were instances where we learned to communicate with each other better.  I know that we are closer because of this project.  This will be a lengthy post as the project is complete.  It start in late October with the gutting of my old room, that had been used as a interim bedroom prior to our son heading to college and ended with the christening of the room on Good Friday with the initial game being held in the room.
      The room had been and electrical work shop in the basement.  The walls were covered in old paneling, that was rotting along base due to moisture.  Our college age son was looking for some cash so his mom had him strip the walls bare.  At this point I assessed that the moisture issue was largely in part to the poor mortar joint between the masonry wall and concrete floor and the moisture wicking through the block.  I set to clean out the joint along the three exterior walls with a 3/8" masonry bit and hammer drill to a depth of 3/4".  Once the joint was cleaned out I placed a 3/4" backer rod compressed to half its height and poured in a self-leveling waterproof seal.  With that done I moved on to the wall giving it three coats of waterstop paint.  There are no pictures from these early steps but the photo log begins from here.  I would have been happy with the painted block receiving a top coat of a chosen color but my wife told me we were making it a real room; we were going to expend the energy once and do it RIGHT.

      The next step was the installation of insulation board, and furring studs.

      Note the light that for the most part was the only source of light in the room it was hot wired with a pull chain switch to turn it on and of that would be one of the first things to change.  With the walls open I was able to add two outlets along the interior wall and run wiring for a switched set of lights over the game table area.

      As I worked on the interior electrical work my wife charged on with the installation of moisture resistant drywall and taping joints.

      Next my wife installed a hardwood panel and stained it, in the location of the built in bookshelves.

      The interior wall backs up to the media center for the basement, I decided to cut an access to the back of the media center through the wall for easier access to all of the connections.

      I decided the cover the lower portion of the interior wall with a tongue and grove bead board.  We placed a cap shelf at 48" and run variable shelves in the interior stud space for display, and affixed pegboard for hanging figs in blisters.  The outlet will be for future LED lighting.

      With the drywall taped we started to choose colors and pick paints. My five year old son wanted to help and started to paint the north wall.

      Next just some progress shots.  Notice the new overhead lights that are centered over the future gaming location.  These are now tied in with a switch at the door to the room.

      And a size check for the fig shelves.

      The final color selections

      I have this lovely axe that my wife bought for me a number of years ago and I wanted to display it prominently, so one of the areas in the display wall was for it.  The other photo is of the door for the axe display being assembled.

      Look at the cool outlet and light switch plate covers my wife found.

      Remember that wall opening to access the media center on the other side of the wall?  Well the idea I had to cover it was a sewer grate.  We took aluminum stock and fastened it with pop rivets to create the grate, and then sprayed it with hammered metal spray paints, Wrought Iron and Copper for the rusty finish we got.

      In the second photo you can see the start of the bookshelves.  They are made with red oak for all of the supports and maple for the shelves themselves.  The shelves will be 16" deep when complete.
      Progress shots walls painted, floor going in.  I the last two stud bays with all of the electric, intercom and central vac, I chose to cover the bay with a corkboard.

      The doors for the display cases for the axe and our Reaper Paint Medals.

      And additional progress on the shelves.

      The plain west wall got a special wall mural treatment.  This took two tries, as the first ones seams were badly damaged during shipping.  The mural outfit we were working with sent us a second straight away when we sent them photos.  It all worked out great in the end.

      In the middle of this journey Reaper Bones II showed up.

      Shelf progress.


      So it was time to decide in the pegboard loading and filling the bookshelves.




      Room nearing completion

      In between my game table got some loving too.  My wife added some pull out writing area, and some shelves underneath that now contain my Dwarven Forge Corridors.  
      The table is a 3/4", 4' x 8' sheet of plywood, with a whiteboard top, 2" x 4" frame and 4" x 4" post leg construction.  The whiteboard top had a blemish, from years ago, during assembly when a friend helping adhering the whiteboard to the plywood, made a brush contact between the two surfaces coated in contact cement and they STUCK, just like they poke fun of in comedies.  Because of this I placed a new whiteboard top on top of the old one. I considered placing an acrylic sheet on top of the whiteboard. My wife's convinced me, and I went out and purchase a 1/4" sheet of acrylic to place on top, of felt furniture spacers, and then trimmed the edges with oak corner protectors.

      At this opening I had a toast with a bottle of Duchesse de Bourgogne for the room with my friends and family.  In my toast I thanked my wife for all of her hard work in making the game room a success, and making the feast grand with all of the extras she bought for it.

      The spread of food from that first night, that was made awesome by my wife extras to make it grand.

      I wish to post my thanks and love for my wife here as well.  To my Wife! Thank you Babe.
      Comments and questions welcome.
      I will be starting a poll regarding the display of items on the top shelf of the book shelf.  Should the dragons be displayed in their boxes to protect them, or pulled from their boxes to be displayed in their full glory.
  • Create New...