Jump to content

Report

  • Optionally enter a message with your report.

    ×   Pasted as rich text.   Restore formatting

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Similar Content

    • By Rigel
      Slaad from Nolzur's. Blue and Green painted in their normal colors; Death and Gray panted in red and black. 
      Not just for fantasy; also make good spacemonsters and post-apocalyptic mutant/invaders, as shown here.


    • By aku-chan
      Presenting Sir Shelly from Knightmare Games. Sometimes the path of Chaos offers great power, and sometimes you end up needing to stay constantly moist or you die.
       
      Really enjoyed painting this one, he's just so weird looking!
      Still can't paint gems though.
       
      As always, any comments or criticisms are warmly received.
    • By Inarah
      3 new figures and a chance to get the original 10 from a previous project. 
       
      https://www.kickstarter.com/projects/1240892696/three-nomads?ref=discovery&term=miniature
       

       

       
       
    • By aku-chan
      Presenting Screamin' Eddie, purveyor of the finest human meat to be found in all the Radlands! 
       
      Had a lot of fun painting this guy. Originally, he was one of the big Nurgle baddies from Games Workshops Rogue Trader boxset, but I thought he worked well as a more generic Post-Apoc mutant (they all could really). 
       
      As always, any comments or criticisms are warmly received.
    • By Jordan Peacock
      Recently, Modiphius released an STL model of the Corvega Coupe, so fans can 3D-print their own (provided they have access to a 3D printer, of course).  I am fortunate enough to have a friend (Chris Thesing) who actually has *two* 3D printers.  He printed off two runs of the model: one in lower resolution on his older PrintrBot Plus printer (using Solutech PLA filament), and another using his newer, higher-resolution resin printer.
       

      ^^^
      The PLA filament version of the model.  This model prints in two pieces -- one for the undercarriage and wheel hubs, and another for the upper body shell.  Alas, there are no tires, and no separate segments for the gull-wing doors, windows, hood, trunk, etc.  This was printed flat on the bed, and due to the low resolution this of course means a lot of striation on those gently curving surfaces.  (This is how it looked after an initial spritz of white spray primer, as the sheen of the bare plastic was problematic for taking photos of the detail, such as it is.)
       

      ^^^
      On the right is the resin-printed version of the same model.  First off, it's a much higher resolution, but also Chris tried printing it at a 45-degree angle (supported by temporary scaffolding) as he's seen several others do.  I'm not quite sure about the advantages of doing this, but I think it makes a difference, because the curved surfaces of the hood, roof, and trunk are very shallow curves.  Actually, I think if the car were put up straight on its bumper, there'd be the best result, because each of the slices across the car would have a minimum variation of width from one to the next, versus the big jumps in footprint area to each layer when the car is printed right-side-up.  That's just my notion, however; there might be factors I'm unaware of that are contributing to this.
       
      Anyway, on the left is the PLA car, but I've gone back with some sandpaper to try to smooth it out a bit.  The trouble is, I noticed that I'd utterly *destroyed* the shallow scribing detail of the gull-wing doors on the roof, and I was in danger of obliterating the Chryslus symbol on the hood and other such things, so I called it quits after a bit, and hoped I could make up for it by camouflaging the striation with "rust paint" effects.
       
       

       
      Here's a side-by-side of the two models now that each one is a little closer in terms of where I am in the process.  The green car on the left is the PLA model (you can still see the striation despite my sanding), whereas the resin one is the red one on the right.  I went in and painted the window areas and chrome detail in grey, and splashed some paint on the PLA undercarriage in preparation for making it look a bit rusted out.  At this point, I pretty much decided that the resin car is going to look pretty much intact, though a bit grungy, with the thought that it's a car that's been restored Post-War, or has somehow otherwise been kept in relatively good condition.  (I could after all use it as a "show car" for my "Chryslus Show Room" scenario.)
       
       
  • Who's Online   7 Members, 0 Anonymous, 25 Guests (See full list)

×
×
  • Create New...