Jump to content


Recommended Posts

Nice job!

 

Where did you get those alien heads? Are they the bits from Epoch Studios that you mentioned?

  • Like 1

Share this post


Link to post
Share on other sites

Nice job!

 

Where did you get those alien heads? Are they the bits from Epoch Studios that you mentioned?

 

Sorry, I had completely missed this question. The bits are now made by Blue Table Painting, which bought the rights from Epoch. 

  • Like 1

Share this post


Link to post
Share on other sites

Excellent, really alienish well done

Share this post


Link to post
Share on other sites

Would definitely add a different flavor to a game o' Space Hulk...

  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By lazarp
      So this is the first time I tried painting freehand on the shield  This is the end result of the conversion: 
       

       
      And for the conversion part, I didn't like neither this minis pose, nor its weapon choice (pickaxe really???), nor its commie looking (???) sigil on the shield. So I removed the weapon and sanded the shield. I also think that his pose looks a lot more natural as a spear throw than a pickaxe swing.. Also gave him some simple terrain and a quick paint  Thanks for looking!
       


    • By lazarp
      Gave this model a different arm and hand pose, sculpted a wooden stick and used a resin bit from avatars of war necromancer for the spear head. This was a speedpaint that took probably around an hour. Thanks for looking!
       

       

       
      The original model:

    • By planetmut
      Vending Machine Tech (Grade C) Dave thought he'd sneak off to Deck 17 for a quick cig.
       
      Dave can rest in peace knowing the rest of his crew will be dead in 11 hours, the Hyperion mining colony slaughtered by Monday and Earth's population wiped out by July.
       
      (I cannot believe I primed, based, shaded/highlighted the parasite only to end up plastering it in Vallejo Red and B4TBG)
       

       

       

    • By Metalchaos
      Hi everyone, I recently had the pleasure of realizing that I inadvertently bought the same Gnoll model twice. So, I decided to convert two of them to create a little variety in my hunting party. Read the text under each picture to have more detail. This post was purposely written as a guide for any who would like to try their hands at converting Reaper Bones model or any other models.
       
       
      I used two 77236 Bloodmane the Gnoll Warrior sculpted by Tre Manor, 77235 Toghra the Gnoll Leader sculpted by Jason Wiebe and 14056 Weapon Pack 1 sculpted by Tim Kaufman.
       

       
       
      I first separated the dagger handle from the body. Just a simple notch did the trick.
       

       
       
      I then cut the trunk along the belt.
       

       
       
      Again, on the other side of the model, I cut the body following the belt as a guide.
       

       
       
      I have this hollow feeling in my stomach...
       

       
       
      Same thing for Toghra, cut the body along the belt line.
       

       
       
      I drilled a hole in Toghra’s lower section and cut a small nail to pin the two parts together.
       

       
       
      I drilled a hole in Bloodmane’s upper body section and tested the pin in.
       

       
       
      I glued the pin in the leg part. I’m using Gorilla Super Glue.
       

       
       
      I then removed the handaxe cutting the handle just above the fist. I keep it for later use.
       

       
       
      The tricky part is to drill a hole in straight line through the fist. I had to use a small drill bit, smaller than the new weapon handle not to tear the plastic.
       

       
       
      I used a slightly bigger drill bit to get the hole a little larger.
       

       
       
      After cleaning the mold line on the new weapon, I cut the handle in halves in order to keep the pommel intact.
       

       
       
      I had to use a file to reduce the diameter of the handle.
       

       
       
      Also, I removed two spikes from the shield to alter its aspect from the one the other Gnoll Worrior is wearing.
       

       
       
      Finally, I’m using a piece of wooden stick to adjust the posture of the model on its base.
       

       
       
      I often use this simple trick to level my models. I use super glue to fix the parts together.
       

       
       
      I’m using 40mm round base for the Gnoll. These models are large and even if there in game space size is 25mm, I personally prefer larger base to have more room for decoration.
       

       
       
      That’s it, I’ll need to fill the gap above the belt and along the shoulder.
       

       
       
      I’ll also be using Greenstuff to fill the gap and complete the base before cleaning everything with soft soap and water prior to painting.
       

       
       
      I added some notches on the cutting edge of the original Gnoll’s plastic axe. I’ll be using it as a battlefield wreck weapon to decorate the base.
       

       
    • By Metalchaos
      02757, Gastaroth the Vampire sculpted by Werner Klocke riding a 02739, Dire Bat sculpted by Jason Wiebe.
      I changed the blades of his two swords for new ones from the 02455, Weapons Pack IV, by Werner Klocke.
       

       

       

       

  • Who's Online   19 Members, 4 Anonymous, 83 Guests (See full list)

×