-
Recently Browsing 0 members
No registered users viewing this page.
-
Similar Content
-
By Maledrakh
The Dragonman something from the Bones 4 core set. This mini actually comes in many parts and with a selection of different weaponry and hand-held things. I went with the bucaneery sabre and dagger on account of the high boots looking a little piratey. Also, this is what the render shown in the KS looked like.
I went with a bronze / gold armour and my new darker flock mix. Turned out well in my opinion at least.
The base is a 3D printed 35x25mm lipped oval as I thought a 40mm round was too large.
B4Core #16 Dragonman (?)
Reaper Miniatures, Bones 4 KS 2017
unknown sculptor
Bonesium PVC.
35x25mm 3D printed oval lipped base
should be available from reapermini.com some time in the future
-
By Maledrakh
This one has been standing around half-painted for a while. The rule 63 Drizzt Do'Urden from Bones 2.
This model is quite nice from the front and back, but really flat from the side. Which is typical of originally made for single piece metal casting-minis.
Your panther has made a mess of my carpet! Come clean it up!
77217 Mi-Sher, female elf with scimitars
Reaper Miniatures, Bones 2 KS 2013 core set
Sculpted by Julie Guthrie
Bonesium PVC.
30mm lipped base
available from reapermini.com
-
By Maledrakh
These scenery bits are from the Bones 2 and 4 kickstarters respectively. I did them quick in my go-to rock paint scheme. An uneven coat of dark greengrey over a solid black undercoat, followed by a heavy drybrush with a sandy yellow, and finished with a lighter drybrush of offwhite. Quick and easy! The colours give a much more satisfying rock finish than just using the typical monochrome greys.
Too bad the colours are not really showing properly up in the photos.
On each end are the Pillars of Good and Evil from Bones 2, the rest is the subset "Grave Things" from the Bones 4 core set.
The Pillar of Evil to the left, the Pillar of Good to the right.
They are made in the older Bonesium PVC material, and as you can see it shows. No amount of the hot water trick is going to correct that warped listing there. I have not seen the metal versions so I cannot compare them with the Bones or even say that the metal ones do no list in the same way (though I doubt that they do.)
I would have thought it be more fitting if these came as a pair of each and not just one of each, but there we are. They are sold as single packs in retail anyway.
77246 Pillar of Good
77247 Pillar of Evil
Reaper Miniatures, Bones 2 KS 2013 Core set, Dungeon Décor subset
Sculpted by Sandra Garrity
Bonesium PVC.
30mm round lipped based
available from reapermini.com
These are from the subset "Grave things" in the Bones 4 Core set. Listing again! I was unsuccessful in trying to unbend the batty one as it bent back over time. Should have left it longer in the hot water. Oh well.
Again, they should have come in a pairs of each.
It seems Bones really is not the best material for boxes with square corners and all that...must be that corrupting influence of the Warp.
This one is OK and untainted by the warp though. The loose books are a nice touch.
Tiny glyphs and imaginary writing that looks much better (and way more impressive) when not magnified, as does most of my painting. The page is actually about 10mm wide. The black symbols and all that are done with .01mm and .02mm pens.
klatoo...berata....nih*cough cough* Ok, then, thats it! *takes book, thunder rumbles* Hey wait a minute! I said the words! I did!
B4Core #126, #127, #128 and #129 Grave Things
Reaper Miniatures, Bones 4 KS 2017
Unknown sculptor
Bonesium PVC.
40mm 3D-printed round lipped base on the statues
should be available from reapermini.com some time in the future
-
By Chaoswolf
Ok, here are the rules:
1) Please don't sign up if you were there, or if you had someone get you stuff from the con. This is supposed to be for people who weren't there. No, I'm not going to check, but the gods will know, and they will visit a terrible vengeance upon you.
2) Unlike the regular version of the BoGW that you may be familiar with, you don't need to match anything you take. All of this stuff was donated by people to allow other people to get some cool stuff. So, take whatever you want (but see below).
3) No sharing your picks. If it works out that everyone involved gets to pick 3 figures but you only want 2, you can't pass that extra figure choice down the line to someone else. Everyone gets to have the same amount of stuff, unless someone chooses to take less. If there's stuff left over, send it back to me and it'll get folded into the next regular Box of Goodwill. (Exact number of choices will be based on the amount of people signing up)
Most of the stuff this time around is metal and resin miniatures. There are no Bones (I did receive a few of the monthly Bones giveaway figure, but they're all the same figure, and I was probably only going to throw in a few to round out numbers if it becomes necessary, otherwise, I was going to put them in the regular BoGW). There are a few non-miniature items, such as bags, dice, etc. There are not enough of these items to go around, so if you want a bag, for example, that counts as one of your picks.
Any other questions, please let me know.
-
By Maledrakh
From WizKids' line of Nolzur's Marvellous Miniatures comes the "Treant", which is D&D-speak for Ent, or Treeman if you are more familar with Warhammer.
I find this mini looks angry and scary, not like a benevolent living tree shepherd at all. A malevolent one, on the other hand, fits the bill precicely.
And seeing as I have been painting undead halflings and there is a strong historic connection between Halflings and Treemen as allies; so undead treeman.
Hence, Torchwood the Furious here.
Go on, you know you want to go on:
-
-
Who's Online 24 Members, 2 Anonymous, 180 Guests (See full list)
