Jump to content

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Metalchaos
      Hi everyone, I recently had the pleasure of realizing that I inadvertently bought the same Gnoll model twice. So, I decided to convert two of them to create a little variety in my hunting party. Read the text under each picture to have more detail. This post was purposely written as a guide for any who would like to try their hands at converting Reaper Bones model or any other models.
       
       
      I used two 77236 Bloodmane the Gnoll Warrior sculpted by Tre Manor, 77235 Toghra the Gnoll Leader sculpted by Jason Wiebe and 14056 Weapon Pack 1 sculpted by Tim Kaufman.
       

       
       
      I first separated the dagger handle from the body. Just a simple notch did the trick.
       

       
       
      I then cut the trunk along the belt.
       

       
       
      Again, on the other side of the model, I cut the body following the belt as a guide.
       

       
       
      I have this hollow feeling in my stomach...
       

       
       
      Same thing for Toghra, cut the body along the belt line.
       

       
       
      I drilled a hole in Toghra’s lower section and cut a small nail to pin the two parts together.
       

       
       
      I drilled a hole in Bloodmane’s upper body section and tested the pin in.
       

       
       
      I glued the pin in the leg part. I’m using Gorilla Super Glue.
       

       
       
      I then removed the handaxe cutting the handle just above the fist. I keep it for later use.
       

       
       
      The tricky part is to drill a hole in straight line through the fist. I had to use a small drill bit, smaller than the new weapon handle not to tear the plastic.
       

       
       
      I used a slightly bigger drill bit to get the hole a little larger.
       

       
       
      After cleaning the mold line on the new weapon, I cut the handle in halves in order to keep the pommel intact.
       

       
       
      I had to use a file to reduce the diameter of the handle.
       

       
       
      Also, I removed two spikes from the shield to alter its aspect from the one the other Gnoll Worrior is wearing.
       

       
       
      Finally, I’m using a piece of wooden stick to adjust the posture of the model on its base.
       

       
       
      I often use this simple trick to level my models. I use super glue to fix the parts together.
       

       
       
      I’m using 40mm round base for the Gnoll. These models are large and even if there in game space size is 25mm, I personally prefer larger base to have more room for decoration.
       

       
       
      That’s it, I’ll need to fill the gap above the belt and along the shoulder.
       

       
       
      I’ll also be using Greenstuff to fill the gap and complete the base before cleaning everything with soft soap and water prior to painting.
       

       
       
      I added some notches on the cutting edge of the original Gnoll’s plastic axe. I’ll be using it as a battlefield wreck weapon to decorate the base.
       

       
    • By Metalchaos
      02757, Gastaroth the Vampire sculpted by Werner Klocke riding a 02739, Dire Bat sculpted by Jason Wiebe.
      I changed the blades of his two swords for new ones from the 02455, Weapons Pack IV, by Werner Klocke.
       

       

       

       

    • By SGHawkins09
      Not sure if this belongs here or under conversions but since I need help/feedback on the sculpting, I figured here was better. 
       
      I am adding puffy sleeves to a figure and I am very much a novice when it comes to sculpting. I have been working on one and while it looks good to me, I need a second opinion. What do you guys think?
       

    • By Chris Palmer
      This past week I painted the Female Devil "Tormentor" figure from the Bones 4 Bedeviled group from the Core Set.   During the run of the Kickstarter, there were folks in the Bones 4 Enthusiasm who where considering the possibilities of  converting the larger Rulers of Hell figure set into some sort of Forest King and Queen creatures by removing their wings and skull iconography.   With the cloven hooves and horns I could see how easily this could be done.  And, while I didn't get that set, I did get the smaller sized Bedeviled group that came in the Core Set.  Looking at the female figure in that set, it seemed to me that she too would be an easy conversion to make into some sort of Faun-like Forest Creature.
       
      Photos linked for nudity.
       
      Link
       
      Link
       
      Link
       
       

       
      For my full conversion and painting article, see: http://allbonesabout.blogspot.com/2019/06/tormentor-female-devil-to-forest.html
       
       
       
    • By Metalchaos
      Hi everyone, Now that the contest is over, here are more pictures of my converted 77038, Hell Hound. The original sculpt is by Ben Siens. This was my entry in Reaper's Facebook Convert and Paint contest. Khan is my elf riding dog in our D&D campaign. The contest was the perfect pretexte to make this conversion. I first removed all the spikes and flames on the hound's back. I then built the armor and saddle using green stuff and a paperclip. The chest is from Reaper's 02638, adventuring accessories. There were amazing entries in the contest and I managed to get an honorable mention. Thanks to Reaper miniatures and Matthew Clark for organizing this contest.
       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

       

  • Who's Online   22 Members, 1 Anonymous, 114 Guests (See full list)

×