Jump to content
  • Optionally enter a message with your report.

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Jordan Peacock
      Recently, Modiphius released an STL model of the Corvega Coupe, so fans can 3D-print their own (provided they have access to a 3D printer, of course).  I am fortunate enough to have a friend (Chris Thesing) who actually has *two* 3D printers.  He printed off two runs of the model: one in lower resolution on his older PrintrBot Plus printer (using Solutech PLA filament), and another using his newer, higher-resolution resin printer.
       

      ^^^
      The PLA filament version of the model.  This model prints in two pieces -- one for the undercarriage and wheel hubs, and another for the upper body shell.  Alas, there are no tires, and no separate segments for the gull-wing doors, windows, hood, trunk, etc.  This was printed flat on the bed, and due to the low resolution this of course means a lot of striation on those gently curving surfaces.  (This is how it looked after an initial spritz of white spray primer, as the sheen of the bare plastic was problematic for taking photos of the detail, such as it is.)
       

      ^^^
      On the right is the resin-printed version of the same model.  First off, it's a much higher resolution, but also Chris tried printing it at a 45-degree angle (supported by temporary scaffolding) as he's seen several others do.  I'm not quite sure about the advantages of doing this, but I think it makes a difference, because the curved surfaces of the hood, roof, and trunk are very shallow curves.  Actually, I think if the car were put up straight on its bumper, there'd be the best result, because each of the slices across the car would have a minimum variation of width from one to the next, versus the big jumps in footprint area to each layer when the car is printed right-side-up.  That's just my notion, however; there might be factors I'm unaware of that are contributing to this.
       
      Anyway, on the left is the PLA car, but I've gone back with some sandpaper to try to smooth it out a bit.  The trouble is, I noticed that I'd utterly *destroyed* the shallow scribing detail of the gull-wing doors on the roof, and I was in danger of obliterating the Chryslus symbol on the hood and other such things, so I called it quits after a bit, and hoped I could make up for it by camouflaging the striation with "rust paint" effects.
       
       

       
      Here's a side-by-side of the two models now that each one is a little closer in terms of where I am in the process.  The green car on the left is the PLA model (you can still see the striation despite my sanding), whereas the resin one is the red one on the right.  I went in and painted the window areas and chrome detail in grey, and splashed some paint on the PLA undercarriage in preparation for making it look a bit rusted out.  At this point, I pretty much decided that the resin car is going to look pretty much intact, though a bit grungy, with the thought that it's a car that's been restored Post-War, or has somehow otherwise been kept in relatively good condition.  (I could after all use it as a "show car" for my "Chryslus Show Room" scenario.)
       
       
    • By lexomatic
      So I got a newsletter with super early (2020) kickstarter tease (image behind the spoiler).
       
       
    • By snitchythedog
      Well mostly scenic base.  Made a town centre that will get dressed up as a market once finished. Basing material is foamex with a plastic receipt spool covered in Milliput.  Painted with a mix of craft, PP and GW paints.  Further tinted with a treatment of oils. 



    • By Jordan Peacock
      Online, from a certain market of miniatures, I found some "Kaosball" team expansion packs on clearance (for a better price than what they're listed at now, as of this writing).  Each pack contains 13 32mm-scale minis in 2 poses (6 of one pose on 25mm square bases, and 7 of an alt pose on 25mm round bases), a "bust" that represents the "team coach," and a game-specific 12-sided die (which I suppose isn't much use for anything, unless I actually wanted to play the game).  Anyway, this worked out to being under $1 a figure, and the sculpts looked interesting, so I got a few packs.  (I find it hilarious, though, that while most of the packs are marked down, the "Felinia Hellcats" -- scantily-clad gun-toting cat-girls -- are specifically marked as "[CLEARANCE]" and yet they're priced at about 3x the asking price for each of the other teams.)
       
      I originally picked these guys up (the "Samaria Barbarians") with a vague intent that "someday" I would run a Savage Worlds convention one-shot scenario heavily inspired by the "Brütal Legend" video game ... but it occurred to me that few if any of my players would have heard of that game, and I'm no particular "expert" on anything rock-and-roll-related, so maybe I'm not the best person to GM such a setting.

      However, I could always use a few more post-apocalyptic wastelanders.  The "big hair" style here doesn't necessarily look like it would fit the current Fallout aesthetic as established in Fallout 4 and Fallout 76, but I think these guys wouldn't look terribly out of place in the original Fallout 1 & 2 (what with all the "Mad Max" and "Fist of the North Star" wannabes wandering about in those games).  I removed the figures from their bases, putty-and-texture-stamped the 25mm round bases, putty-and-texture-stamped some plastic 25mm rounds for the remaining figures, and did a few hand swaps and bit-add-ons to give a few of the figures visible ranged weaponry.  (I figured that would give me a little more buy-in if I were to field a gang of these guys for an encounter and then they start FIRING on the PCs, versus what pushback I might get if they *appeared* to only be armed with axes.)

      I used some paper printed license plates to add some "junk armor" elements to further reinforce the "post-apocalyptic" vibe.

      Each team pack also comes with a "bust" to represent the team coach.  I went with a bronze-and-verdigris scheme for each.
    • By lexomatic
      Came across this article. Oh to have money, time, and space.
       
      "The scenery and structures are his forte, rather than the locomotives and tracks. "I find beauty in what everyone else sees as ugly - rugged skyscrapers, beaten-up warehouses, things that are very run down."
  • Who's Online   24 Members, 1 Anonymous, 38 Guests (See full list)

×
×
  • Create New...