Jump to content

knarthex

FOR SCIENCE! Knarthex tests Vallejo Masking Fluid

Recommended Posts

So,

Our own Wizard most Wild mentioned getting this stuff and finding that it worked for him, so I ordered a bottle of it, as I do a little airbrushing from time to time....

 

I spent 2 hours or so looking at videos on youtube about how this stuff is used, and decided that the Wolf Demon (77307), that I used for the Hangout Airbrush tutorials last year, would be a good test subject for it, as I was not going to jump straight onto Nathvarr...

 

The first recommendation I followed was to spray the model with Glosscote, to protect the paint underneath.

001.thumb.JPG.df0122e4a3f2137f59f4a01da619331c.JPG002.thumb.JPG.daf01fec952208617c82a4c95cb104b7.JPG003.thumb.JPG.30036fd31708227918a2f7a02d9f7436.JPG004.JPG.4079a77906e34136fdb57e348f91c912.JPG

I then, again following a tutorial, I daubed the stuff on with a semi junk brush, and let it dry,

006.thumb.JPG.41d1e8a33e37b2f4837d7f70705b563c.JPG007.thumb.JPG.1b7f3cfe81e97f4db668b2fdd2072054.JPG008.thumb.JPG.1be529bc95df8375bfe2569304ab4cef.JPG009.thumb.JPG.73b1b4bce066d14101c4f3d90d146db8.JPG

I then did another coat, and this is what it looked like after it dried...

(Taken at the end of my paint session last night)

024.JPG.91b64f4220e7d55905f98403f4077983.JPG025.JPG.c671bef312edb98af03adfea8b4ff19a.JPG026.JPG.4020ccb545e7ddafa796f1b1038c7db0.JPG027.JPG.cf66e57b041b4dfc77552f71e595590a.JPG

so tonight will see if it works....

 

ALSO, in one of the tutorials, the artist was coating his W&N SERIES 7 (!) brush with brush soap before painting this stuff on....:blink:

The brush I used was one that I liked to use for painting bases and such, and it is pretty much trash by now, even after rinsing often and an overnight soak in W&N Brush Cleaner & Restorer...

RIP>>>>

Edited by knarthex
  • Like 10

Share this post


Link to post
Share on other sites

I must say I keep wondering how easily masking fluid can be removed on minis that have lots of nooks and crannies.

 

I've never tried artist's masking fluid, but my mind keeps gong back to regular tape that can tear away part of whatever was underneath it, or dried white glue on your hand that never seems to completely get off without ripping or leaving residue.

Share this post


Link to post
Share on other sites

I've not tried using masking fluid or tape on human-sized 28mm minis before, but I have on large-scale figures and large minis like Kaladrax.  I've found from experience that what works best is a combination of low-tack painter's tape covering the majority of the area to be masked, and masking fluid around the edges and across any tape joins.  That seems to work best at avoiding any accidental overspray where the tape may have lifted or didn't quite overlap.

 

If you've cleaned and primed well, and not handled the figure with oily hands while painting, there should be no problem with paint lifting off.  If you pull tape / fluid away doubled over and flat against the surface, that should minimize lifting more than pulling it straight up.  Pulling it away flat at a 90 degree bend from the mask line also works well to minimize lifting or tearing of the paint.

 

Clean up any overspray or jagged edges with a detail paintbrush.

 

Edit:  Oh, and it helps to make little tabs of tape or loops of string embedded in the masking fluid, so you can start pulling off the mask without scratching at it. 

Edited by Grumpy Cave Bear
  • Like 2

Share this post


Link to post
Share on other sites

So the ending results....

Painting on top of the mask...

001.JPG.2d10296f0277c8f09d27c2ee2cd519b8.JPG002.JPG.93ca77f221d2a2d6cc24733433bbb59c.JPG003.JPG.059428ac71856e87e4827649ab4531a4.JPG004.JPG.d93f8399592ae41884cf6290fa3d3fa8.JPG

and with the mask being removed...

005.thumb.JPG.a47cb3117729bb765dbe769a1da1accc.JPG006.thumb.JPG.0b82c110e7aa16b614d88dde0142b62e.JPG007.thumb.JPG.3b0af475f3d21f2291072044f58f3c2d.JPG008.thumb.JPG.aefe4aa6b0741cf951b3182b5a7130bc.JPG

and all removed...

009.JPG.e7eabba512bc2ebba756e408f98c3d44.JPG010.JPG.3fec536fd7e2a76af752f16f815f9637.JPG012.JPG.97740c159357b43fdb986786e2eb6f33.JPG

So I am pleased with this stuff, and have painted it on the Dragon...

 

Thanks for looking!

Feel free to ask questions!

I will answer to the best of my ability!

011.JPG

  • Like 7

Share this post


Link to post
Share on other sites

I just rubbed it gently with my thum, and it started rolling up for me...

I could then grab it with tweezers and pull it away. ..

  • Like 3

Share this post


Link to post
Share on other sites

I think I just had an epiphany.

 

I kept wondering if I'd be interested in masking fluid or not and couldn't find any good reasons... until I remembered how I and everyone hates painting eyes, and how often a stray stroke ruins everything.

 

Masking fluid would provide the perfect "shield" for eyes, wouldn't it?

  • Like 3

Share this post


Link to post
Share on other sites
On 5/3/2017 at 6:27 AM, Cranky Dog said:

I think I just had an epiphany.

 

I kept wondering if I'd be interested in masking fluid or not and couldn't find any good reasons... until I remembered how I and everyone hates painting eyes, and how often a stray stroke ruins everything.

 

Masking fluid would provide the perfect "shield" for eyes, wouldn't it?

 

Masking fluid would be pretty good for protecting the face from stray brush strokes, once the eyes were painted.

  • Like 2

Share this post


Link to post
Share on other sites

So...

I finished up airbrushing the masked dragon, and sprayed it with DullCote to protect the paint from my fingers rubbing of the mask...

 

I then began rubbing off the mask....

 

Tip #1 Put the stuff on THICK!!!!

I did 2 coats thinking that would be enough.... Next time I will do at least 4 to make the peeling easier, as it tends to be difficult to get out of very deep places if it isn't thick enough....

 

Tip #2 Check what you have done for good coverage!

As I peeled it off, I found places that I missed when applying the mask... Wish the stuff dryed opaque...

 

so some close up pics of spots that I either missed, or still need to get the last bits of mask out of....

008.JPG.58207d5a2e8c0f1879f715e612743538.JPG009.JPG.4dff372eb8bd65e7d581672cd38065d0.JPG010.JPG.5f2a90cf76c843b2b2e4d1628f5722f2.JPG011.thumb.JPG.2a02f8337c7086254d8fc3ca671503ed.JPG012.JPG.6442870ac1e09d56e0fb91da071f92d6.JPG

Thanks for looking!

  • Like 6

Share this post


Link to post
Share on other sites

Yeah, slow & steady a few times around the edges will help with coverage.  That's why I tend to cover most of the area with painter's tape, then use several layers of liquid mask around the edges.  That way, I know I've covered most everything thoroughly.

 

There are some liquid masks that have some coloring in them, but they tend to be transparent and mostly just show up over white when dry.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Shogun
      I'm taking the leap and about to buy my first airbrush for mini painting and was hoping I could get some advice on what to buy. The Airbrushing: compendium has been very helpful and I've spent hours, days, what feels like years researching and I want to pull the trigger... I live in Canada and after ringing around some hobbyshops etc it seems amazon is the best bang for my buck. I have paint and access to a Campbell Hausfeld 2 Gallon Air Compressor (I will purchase another compressor in a few months once I have some more disposable income). My main concerns are does this compressor work with the airbrush listed below, do I need anything else? Heres what I've got in mind:   NEO CN GRAVITY-FEED DUAL-ACTION AIRBRUSH $97.20 CAD Paasche 10-foot Nylon Braided Hose $18 CAD Airbrush Cleaner 4 Kit, Washing Tools - Glass Cleaning Pot etc $22 CAD Vallejo Airbrush Cleaner 85ml $7 CAD   any advice would be appreciated
    • By Pineapple
      These are from the Ghosts of Midlam Manor Kickstarter.  I love these sculpts and I just got an airbrush, so I wanted to try sort of a blue zenithal ghost effect.  They are more blue than the camera shows, I'm still getting used to the photo booth and lighting.  (Plus I should probably use the real camera instead of my phone.)
       
      Overall I'm happy!
       

       

       

       

       

       

    • By Pineapple
      As with the other ghosts, I was playing around with quickly airbrushing a ghost effect.  I liked the green tone of these Bones 4 minis, but I'm not a big fan of translucent figures.  I wanted to paint over them, but keep the ghost vibe.  These are much greener in person.  I like them, but I think the blue ghosts in the other thread turned out a tad better.  These ended up a hair too bright for what I was going for, but it's all in the name of science! I might glaze them down a bit later.
       

       

       

       

       

       

       
       
    • By Mckenna35
      I've had this kit for quite a while now, to build for a friend who's a big Judge Dredd fan.  Due to circumstances I can't go into, he asked me if I could this one, along with Judge Anderson and possibly Judge Death put together and painted for him.  Second vinyl figure I've worked on, and I thought some of you might find it interesting.  First picture shows the components cut out and cleaned up.  The second is the major subassemblies.


      One of the tricks with this kind of kit is to fill the lower portions with plaster to add rigidity, weight and strength to the piece.  Without it, you run the risk of the vinyl buckling if it gets too hot after you've got the figure assembled.  Yeah, DON'T leave these kits out in direct sunlight!  
       

       
      and here he is with all the primary assembly complete and ready for paint:

    • By paedia
      [Warning: lots of images incoming]
       
      Next up on my table are the miniatures from Cerebria: The Inside World, a boardgame from Mindclash Games in which the forces of Bliss and Gloom vie for control of an evolving personality.
       
      I'm going to try to do these two at a time (one from each team); the first two will be Harmony and Malice.

      Session 1 - prime + zenithal highlight
       
      Harmony

       
      Malice

       
      Session 2
       
      Harmony
      With the airbrush, I did base+shading of the wings and base of the body. Colors used:
      - Twilight Blue
      - Snow Shadow
      - Surf Aqua
      - Violet Light
      - Sunset Purple
      - Maggot White

       
      Malice
      For malice, I'm starting with the NMM-bronze-ish body. I base coated with Khaki Shadow, then used Ghoul Skin and Moldy Skin for initial highlighting. Shadows are Woodstain Brown and NMM Gold Shadow (which I am not that fond of for Gold, but seems to work well here). Any other color recommendations? I finished up the session with basing the skirt in Redstone.

  • Who's Online   14 Members, 0 Anonymous, 45 Guests (See full list)

×