Jump to content

Recommended Posts

So here we go.  Discovered a problem. My socket idea for adding different accessories is probably not going to work.  My slicing software (the software that converts the digital files into code for the printer) puts supports in the sockets that are proving to be difficult to dig out.  So I'm going to have to revisit that idea, and perhaps just build those details in.  The hatches, though, proved to work just like I wanted them to.  By using a small piece of raw filament as the hinge pin, I can pose them closed or open at any angle.  For robustness, I'll probably have to glue them in a single position though, just to keep them from breaking later on. 

TychoUpperHullPrintFrontSmal_111517.thumb.png.7d793b6157392a9a76b140bcee95e1a8.png

TychoUpperHullPrintRearSmall_111517.thumb.png.0224b6eca4cebc706f24bc04333c8cb5.png

 

And the first half of the turret just finished printing!

  • Like 3
Link to post
Share on other sites
10 minutes ago, chaosscorpion said:

Do you plan to sand the planes of the APC smooth?

Yes.  There will be a round of sanding, followed by a coat of primer, followed by a  second round of sanding, followed by a second round of primer, followed by a third round of sanding, followed by my base coat.  At that point, it should look relatively smooth. 

Visually, it appears rougher than it is texture-wise, especially in the photos. 

 

Link to post
Share on other sites

OK, so my "sculpt" is done, all the pieces are printed. There are some things I'll be tweaking before my next print and upload to Thingiverse, but for the most part, here's the "finished" product.

The upper hull, which I've shown before:

Tycho_UpperHull_111517small.thumb.png.75bf25751feb0d65acca4f619ee07180.png

 

The lower hull. I was going to try something that looked like big fan blades, but I gave up. The two holes at either end are for the flight stands.
Tycho_LowerHull_111517small.thumb.png.309b916dc4e5a63a1a6cc7e8b5c5355e.png

 

The two halves of the turret. I have been using small holes and pieces of raw filament as a way of lining pieces up and holding them together:

Tycho_TurretHalves_111517small.thumb.png.511610f8e3246cd4eefdda5fe2314da5.png

The hatches. You can see where I've used raw filament as a hinge pin:

Tycho_Hatches_111517small.thumb.png.622919712e9467c010de20990ecca7f1.png
 

The main gun, with both barrel options:

Tycho_MainGuns_111517small.thumb.png.8e8f4ab2a6e0988730c036c589999688.png

And finally, the whole thing, fitted together, up on some Reaper Flight stands, along with the NOVA Corp soldier who will be assigned as the tank commander:

Tycho_onBase3_111517small.thumb.png.f15ba6882521e4c5ed76491be30efb2f.png

 

Since the "sculpt" portion is done, I'll be making a Work In Progress thread for the assembly and painting. 

 

  • Like 9
Link to post
Share on other sites
  • 3 weeks later...
21 hours ago, Crowley said:

That's really cool!!

Thanks.  It's been really fun seeing something go straight from my imagination to being a final product, AND be 100% reproducible.  I've scratch built vehicles before, but they've always ended up being a one off thing. 

  • Like 2
Link to post
Share on other sites
On 12/10/2017 at 1:15 PM, kristof65 said:

Thanks.  It's been really fun seeing something go straight from my imagination to being a final product, AND be 100% reproducible.  I've scratch built vehicles before, but they've always ended up being a one off thing. 

 

Nice, innit? I’ve thoroughly enjoyed the vehicles I’ve made, and plan more of them, too. 

  • Like 1
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Erramir Orlans
      Hello people! i would like to share with you an upcoming Kickstarter campaign that will start on April 20 and last until May 10.
       
      This is the preview page https://www.kickstarter.com/projects/joygamesinteractive/the-holy-roman-empire?ref=d1ay07&token=6758305e
       

      As the title says, it will offer Rank & file 3d printable models to make an Imperial Army (15-16th century Germany/Holy Roman Empire), including chracters, commanders, and special troops/artillery
      The main pledge of $30 usd, gives 63 models (core units). As add-ons, at 75% off (compared to webstore prices), there will be sets of models (from previous releases in the patreon) and scenery.
       
      The base pledge:
       

      There will be some freebies stretch goals, and other payed, Like ogres mercenaries(x3), Giant, volley gun, heavy arquebusier/sharpshooter, and moarrr!
    • By Metalchaos
      Hi everyone, I'm almost running out of prep/primed minis so, I'm preparing some more. I recently painted a Dark Dwarf Striker and like the model so much I decided to paint the other models. Also, I wanted to convert an enlarged model to make it look more like the Striker instead of the Smiter. I made a 3D model of the hammer head and 3D printed it. Here are some pictures of my advancement so far.
       

       

       

       

       

       

       

       

       

       

       

    • By Reverend Shartan
      I have condition markers, and other markers numbered 1-20 for monsters/enemies, etc. I want to do these on my Mars, but I don't know if they should be printed flat, or at the "suggested" 30 degree incline. If they should be done inclined, how light or heavy, should I do supports?
       
      Any help or suggestions are appreciated.
       
      Edit: Tried printing the marker flat on the build plate - nothing was printed. So, now trying parallel to the bed, but with supports
       
      Reverend Shartan
    • By prophetic_joe
      Here is my tortle monk printed on an inexpensive resin printer.
       



    • By Lidless Eye
      Figured I'd put together one big thread of my recently finished 3D prints.  Everything was printed on an Elegoo Mars.

      Titan Behemoth from Duncan Shadow Louca:



      Cyclops Behemoth, also from Duncan Shadow Louca:



      A scale shot of those two, with Sir Forscale and a not-Johann the Running Man as my plastic one is broken:



      Which leads into:

       
      "You don't STINK like a peasant." "You don't DRESS like a peasant." "And you're definitely not ON FIRE like a peasant."
      Fleeing Peasants off Thingiverse:
       



      "So yeah, the treasure chest gets up and decks you."

      Brawler Mimics off Thingiverse:


       
      Vapour Snakes off Thingiverse:




      Spell Effects from Vae Victis:


       
       
      Cook, also from Vae Victis:



      Angry Barmaid, from Titan Forge




      Urd, from The Lost Dragons


       

       
  • Who's Online   16 Members, 3 Anonymous, 61 Guests (See full list)

×
×
  • Create New...