Jump to content

Warlord Games M18 Hellcat Tank Destroyer


Savage Coyote
 Share

Recommended Posts

  • Replies 7
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Similar Content

    • By Mckenna35
      Finally finished some support units for my Bolt Action winter Soviets. Observer, medium machine gun, and medium mortar, all 28mm. Should've done some more paint work on the bases before I applied the snow. Oops. They'll look good on the table.






    • By Mckenna35
      Finished a couple more gang members for Warlord Games Judge Dredd game.  Painted with reaper and Vallejo.  In theory they'll get used for demos so I didn't want to burn a lot f time on the bases.  These were some of their first figures in their new resin.  It's kind of like Bones I as far as material goes.  Also think they some of their early  ones in 3d modelling as the "engraving" is almost too light.  makes it hard to pick out details and you've got to be careful not to apply too heavy a coat or you'll fill in lines pretty easily.

    • By odinsgrandson
      Wear and tear is usually a welcome addition to most vehicle models. After all, tank armor is made to take a few hits.
      One of the things to keep in mind when painting something like that is the story it tells. Where and how you place it tells of how the damage happened. Rusty areas are older than shining metal showing through- moreso if there are streaks of rust leading down. A combination of rust and metal shows that this is a place where the rust layer gets scrapped off.
      This vehicle is from Seedy Tea Publishing‘s Simulacrum Protocol line.



    • By Mckenna35
      Street Judge and a couple of members from the street gang box. These are cast in WGs  new resin, and I'm not sure about it. Stuff is very flexible and the detail on the gangers is very shallow so you have use a light touch with the paint and it can be hard to figure out what you're painting. Turned out ok.





    • By GlenP
      Howdy all,
       
      This is Tamiya's 1/35 scale Sherman Jumbo - a significantly up-armored Sherman tank designed to be at the head of advancing columns and function as an assault tank. Two hundred and fifty-four were built through the spring and summer of 1944 with the first batches hitting the European front in the fall of '44. All were initially armed with a 75mm gun. A number were later converted to the long barrel 76mm gun because it fired a more effective high-velocity anti-tank round. The Sherman Jumbos served through the end of the war in Europe.
       
      Tamiya's kit dates back to 1987 and is based on Tamiya's standard M4A3 Sherman tank issued in the early 80s. Tamiya added a new larger turret, new armor plates for the upper hull sides, and a new glacis plate for the hull front. Unfortunately, they neglected to provide a new and much larger front transmission cover. Numerous reviews have also mentioned the turret shape and size are off, but I've yet to read/hear where it's off or by how much. I spent some time looking over book and interweb pics and the height of the turret might be a bit low. Maybe. I believe the Jumbo is out of production, but the originall M4A3 is still available. Not worry; new, more detailed and more complex Jumbos are available.
       
      I've built a new transmission cover using the old cover as a foundation, then adding sheets and strips of Evergreen .040 plastic to beef it up. The turret height was raised with .030 strips of plastic between the upper and lower turret halves. Additional details were added to the hull and turret - basically anywhere you see white, copper wire, brass, or green putty. I also used a Dremel tool and a small dove-tail cutter to enhance the very prominent hull weld beads. The case transmission cover and the turret sides were coated with liquid glue (in sections) and stippled with a siff wire brush to replicate the cast texture of the real items. You can see the turret texture in the photo.
       
      The pic shows the mocked up upper and lower hull components and the turret, three of the six bogie wheel assemblies (three more on the other side), the mantlet, and turned aluminum gun barrel. Painting next - any color you want as long as it's olive-by-God-drab.
       
      Qs and Cs welcomed; no secrets here...
       

×
×
  • Create New...