Jump to content

  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Maledrakh
      From the fourth Bones kickstarter (no, I have not received my shipment yet, not even a shipping notice). This minis was sold online and given as a freebie if you ordered for more than USD 40 from the Reaper site in February this year. When I ordered it I was not aware that this mini also is in the kickstarter. The January freebie owlbear was not a KS mini, so I assumed the Febuary one would be seperate too. So I will be getting another of this mini with the KS shipment.
      So anyway..."Bones Black". a darker grey, much harder, less unbreakable, and heavier material than the regular "Bonesium" Bones material. This new material was a bit of a surprise when announced not too long ago, as there was no mention of it in the Kickstarter. They have gone and produced many of the kickstarter minis in this new material (as in all the expansions, but not the core set). I understand that this material requires a different type of mould which is more expensive to make and maintain, so the Bones Black minis will be slightly more expensive at retail than comparable regular Bones. Reaper is on record stating that they chose the name as it sounded cool. The minis are not actually black, just dark grey.
      My first impressions of the material is that it is actually quite similar -but not identical- to both Restic and the newer Boardgame plastic such as used in HATE. It is very hard and diffcult to cut or bend when at room temperature. I suspect there is ABS in the PVC mix here.
      However, it still responds well to heat (near-boiling water) and goes rubbery soft and reposable just like other PVC minis. When soft, it is comparatively easy to slice with a scalpel hobby knife. Just like Restic, it needs a little time for super glue to grab, and when it does, it grabs firmly. It is easy to drill, and what little mould lines there were came off easily enough with said knife. Not quite as easy as polystyrene, but much easier than original Bones. They could actually be scraped, which does not work at all with regular Bones.
      The troll came assembled, and needed gap filling. Reaper has also addressed this issue, stating that the new material has slightly different tolerances and shrinkage than the original Bones. They have been adjusting the connection points to compensate to avoid such gaps going forward.
      At any rate, my impressions of the Bones Black material are mostly favorable. The biggest con would be that is seems slightly more brittle than the original Bones (that can be thrown around without taking damage), but I have not had any issues with neither this Troll or the Owlbear, so I can't really say.  When the KS arrives I will be able to look at many more minis in this material, so we shall see whether this will be any issue.
      The quality of the details do seem to be rather better than earlier Bones, and this is the reason Reaper has introduced the material in the first place. Again, the smaller minis from the KS will be the proof of the pudding.
       
       
      Should have lit it better...


      And it is BIG! Actually as tall as the Storm Giant, and larger then the new GW Rockgut Troggoths (aka stone trolls)

       
      A quick and sloppy paint job. I started with a black undercoat, and painted the whole piece with a very dark blue. Then I drybrushed the trunk of the body with three different purples, with red on the stomach and chest. I drybrushed the arms and head with Vallejo Nocturna Shadow and ditto Cold Flesh, the belt and loincloth also in Shadow, with Deep Forest Skin for highlights, mixed a bit on my palette for a couple of shades highlighting. The claws and nails were also done in the greens. The leg of cured meat or large pouch (you choose) in browns.
      The crystals and eyes I did in Scalecolor Tesla Blue and Carribean Blue with Reaper Aircraft Grey highlight. This was a bit sloppy as seen in the photos.
      Teeth in Aircraft Grey.
      Base as usual, and it turns out my new Vallejo Black is really glossy.
      All in all the mini took less than an hour to paint.
       
       
      44002 Rock Troll
      Reaper Miniatures, Bones 4 KS
      Sculpted by Jason Wiebe
      Bones Black
      60mm base
      Will be available from reapermini.com at some point in the future when it goes on general retail release.
    • By Maledrakh
      Just a random mini this time, the Stone Giant from the first expansion of the second Bones kickstarter from 2013.
       
       
      Stone Giants are the smallest of the giants, but still much larger than Conan. And have mothers milk that also can be used as spackle.
       
      77336: Stone Giant
      sculpted by Jason Wiebe
      from the Reaper Bones 2 kickstarter
      Made in Bonesium PVC
      50mm base
       
    • By Patrik Strom
      The Celestial Stag from Reaper Miniatures (03907). I painted this for a character in a DnD game that has a habit of shifting into a stag. I'm quite happy with the base.



    • By Cygnwulf
      Everyone, meet Viridius.  

      He's a hefty boi.  No Ma'al or Kalladrax, but still pretty big. He doesn't even fit in my light box, as you can see.   
      I've thought a long time about how I was going to paint him up, I don't think I'm going to go with the standard green dragon look.  Instead I'm going to take my inspiration from the time of year, and make him an autumn forest dragon, whose coloration changes with the forest around him.   So I'll be doing him in mostly golden yellows to oranges and reds, but keeping some greenish tones as the base of scales and other places, to kind of give a reminder of the verdent glory he was before.
       
      One thing I'm choosing to see as an opportunity is that the tops of his wings are very smooth, ideal for some freehand work.  The question is, what to do?  Some kind of leaf like pattern, or perhaps a butterfly like eye pattern (in the leaf colors, of course)
       
      Out of the box bag he was in pretty good shape.  The usual mold line cleanup, though he has some gaps that will need to be filled.  I followed up with reshaping the wings a little with some boiling water.  I forgot to get a complete before picture, but below you can see the before and after for the right wing


       
      I've had to fully assemble him, I don't like the way the wing joins look without greenstuff, so that's going to be the first order of business.  So painting around the wings might be a chore, but it's nothing I haven't dealt with before (Although, not in recent history)

       
      I begain the gapfill on the right side, but after sticking a finger in greenstuff twice and having to flip him back to touch up the texture, I decided to call it a night and do the left side gaps later.

       
       
       
       
       
       
       
    • By Patrik Strom
      The first painted mini of the year! I really love this sculpt. My favorite part by far is the comb over :D I did a poor job of cleaning the miniature before priming and starting to paint it (like always), so there's a bit of grain on the axe and other irregularities. But nothing to harmful.
       
       
       




  • Who's Online   46 Members, 3 Anonymous, 75 Guests (See full list)

×