Jump to content
  • Optionally enter a message with your report.

    ×   Pasted as rich text.   Restore formatting

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Inarah
      This is the Bones version of the iconic character, painted in a rather quick and dirty fashion. There was a lot of metal and chain mail, which I did not spend time on, and a few details which I picked out.  In retrospect I could have brightened up the armor some, but since she's likely to go on the table as a generic fighter I didn't feel the need to make her special. 
       

       

       
    • By Metalchaos
      Hello again, this one is Darkblade, a Wizkids Pathfinder Deep Cuts 72596, Human Male Fighter. Darkblade is also a the character of one of the players of our D&D group. I painted it with Reaper MSP paint.
       

       

       

       

       

       

       

    • By Marsya
      How long has it been since I started a show off thread???? Too long. I have missed everyone and hope to get back to at least a semi regular amount of posts. Figured I’d start with a Reaper mini. For the forum peeps that attended ReaperCon 2019 you may have seen my version of Derek’s beautiful sculpt O-Sayumi or affectionately named Akiko. I had a great time painting this lovely lady. Since I didn’t complete her until Thursday night of the con I didn’t get any photos until last week. Two years to take pics and post them up, not bad huh? 
       
      I missed ReaperCon and all of you. I have been enjoying seeing the pics shared here. So here is to a year of painting more minis and bringing them to Texas in 2022. 
       
      Now without further ado, Akiko. 
       



    • By Inarah
      Merisiel, Iconic Rogue.  The original artwork is very good but this is one of the early Bones models that did not translate well to the medium.   She flops over, the weapons did not come out well, and much of her detail is guesswork.  I even had to sculpt her a nose because she didn't come with one.  I tried to follow the artwork more or less, but it wasn't worth the effort to spend too much time on her. 
       

       

       

       
    • By Darcstaar
      I only saw one thread about crackle paste when I searched these forums.
       
      So, I’m going to share how it’s going for me.
       
      I started with washed and dried 1” and 2” Reaper Bases.
       
      I put this garbage on a 2 inch base first.

      Don’t buy it.  I got it at Hobby Lobby at the time because they were out of Folk Art.
       
      To be clear, this is Crackle Medium.
      It is meant to be painted on a primed or rough surface I guess, and painted thin. I put it on kind of thick.  It didn’t crackle at all!
       
      So, I got a tub of this stuff on Amazon.

      The directions state “put over a thin layer of PVA glue.”  Pfft, who has time for that extra step?
       
      Here is the result on a washed but otherwise un prepped set of bases.

      1 inch
       

      2 inch.
       
      Lousy!
      So, the surface needs something for crackle paste to work right.
       

      This is a 1” base with a thin layer of PVA glue.
       

      This is a 1” base with just hitting it with 220 grit sandpaper and washing it again.
       
      I also used the 2” base with dried crackle medium on it.  Not pictured.

      This is a 2” base covered in black brush on primer.

      Here is the result on the 2” base over dried crackle medium.  It was hard to get the stuff into a uniform layer, as the medium created a very hydrophobic surface, so the paste slides around too easy.
  • Who's Online   11 Members, 0 Anonymous, 25 Guests (See full list)

×
×
  • Create New...