Jump to content
Sign in to follow this  
Smokestack

Legends of Signum

Recommended Posts

I received mine very early on and am super pleased. Despite the freeze and a the drama they delivered and with not too too much delay. Communication was good and the product is good. Quite a bit to assemble but I don't mind that. Happy I backed.

  • Like 1

Share this post


Link to post
Share on other sites

I got mine today, actually had to pick it up from PO cause had to sign for it: resin details look very nice, quite a few fiddly bits though.

  • Like 1

Share this post


Link to post
Share on other sites

Got a 'Ping' on my cell-phone today as I sat down on the bus. The people at the post('post in store' at a grocery store) had just scanned my package in, less than 200 meters from me. 

So close...    

 

  • Like 2

Share this post


Link to post
Share on other sites

Good for you guys. Mine arrived a while back. A few missing components (one sphinx had 2 front left legs & no front right leg, one miniature didn't have  ahead etc). I got in touch and the company has really great customer service. Replacement parts are on their way to me and I'll continue miniature assembly when the missing parts arrive.

 

Be careful with the chaos dwarf sorcerer with 6 tentacles for legs. The tentacles and sockets for them are numbered with Roman numerals. However there is no number 4 and instead you'll get number 6 twice. This is not a packing error. It's an error labelling the parts.  So they go 1,2,3,6,5,6. You just need to dry fit both number 6 tentacles into both number 6 holes and maybe go and take a look at the photos on their webstore before gluing them in place.

  • Like 3
  • Thanks 2

Share this post


Link to post
Share on other sites

I finally got my minis yesterday. I received shipping notice three weeks ago, so it was a long journey. I was a little worried when I saw the box:

4Ab3DHSg.thumb.jpeg.e1cd306d57b8adf5c3a37dd7cc7537a2.jpeg

It had one very bad ding on the corner. Fortunately the minis inside were well packaged and padded, so no damage done.

 

I got the core box plus a few add-ons. I messed up and forgot to order Aria, which really bugs me because I love angelic minis. Still, I did get some nice ones. Queen Zenobia:

RbzjVo5g.thumb.jpeg.c656f0aef00df6f12144fd752bdbe6b5.jpeg

It's a beautiful mini, but requires a lot of assembly (the wings are two pieces each). And the vent pieces that need to be removed are very thick, often thicker than the part they are attached to. For example, on the tabard visible on the front, the whole bottom piece is venting and needs to be removed, but it's much thicker and stronger than the piece it's attached to.

 

Inez Nimble Fingers:

jB5LF5Bw.jpeg.98b167a80f77e24dfd6ab9426fa32c82.jpeg

I couldn't resist such a unique miniature. This is another one that raises some serious concerns with trimming pieces. The pegs for joining are sometimes smaller than the vents, so I'm sure at least some will break. Hopefully I can repair it without too many problems.

 

This is Zaira the Shadow of Grand Master, the super-secret early bird mini. Also the reason I missed out on Aria, for some reason I thought she was the free mini:

GUTH1Z5Q.jpeg.7427c2dff3d03741e689b066c3d5c3ef.jpeg

This is a great looking mini. She's topless, covering herself with her arm and holding a sword in the other. On the left is the base, which includes her shield, breastplate and helm. Play D&D for any length of time and you'll empathize with being caught without your armour on. She also comes with a choice of three heads, seen in the middle. Lots of pieces, but these don't look quite as rough to put together.

 

Tara the Moonblade:

fZDdBIVQ.jpeg.d9f3538be9c301e4aed9621ae38c8785.jpeg

Another mini that should look fantastic assembled, but she's got a lot of vents connected to small tabs that are sure to break during cutting/assembly.

 

Finally I picked up the Forest:

CFe0qVOg.jpeg.bd1f6a9e09d31317f4834dba2e0c04ff.jpeg

I could only easily assemble a few pieces without some serious cutting. There are a lot of vents everywhere needing removal. In the foreground you can see a bird that sits atop one of the bigger tree. Hopefully I can remove it from the vents without damaging it, but the venting is thicker than the legs. It's going to look great fully painted and assembled.

 

The front right tree is two pieces, I broke a tab off when I was trying to assemble it:

MIRibYWQ.jpeg.2f1b1995d0cd9f92976c06b08865068b.jpeg

Fortunately it's just a tree so it's not the end of the world, but it snapped off so easily I am very concerned about the character minis. if you look closely, the left side is the tab that should have remained on the tree, the thicker part is the venting.

 

For all I'm complaining about the vents, I'm happy with the minis. The bigger vents mean less voids, I didn't find a single flaw in these minis. I'm very glad I backed.

  • Like 3

Share this post


Link to post
Share on other sites

Queen Zenobia is massive isn't she?

I'm going to need to apply a little putty to a few gaps in the wings, the lower pointed tip of her breastplate where there was a slight air bubble, and probably one or two other places prior to painting.

 

IMG_3707.JPG.1e66146796c03ce6133114be15a062fc.JPG

 

IMG_3710.JPG.d68f6bd4e80334badc9d6716be014a74.JPG

 

IMG_3708.JPG.0368551eb11a03f15e2e6bf5d3c26535.JPG

 

IMG_3709.JPG.666bd615ec6eea86e3e8563de1c0ac6f.JPG

Edited by Balgin Stondraeg
  • Like 5

Share this post


Link to post
Share on other sites

You may be able to reduce the gaps in her wings by trimming the tab and the matching surfaces around the tab. 

(I've been putzing around with Roland the Pain in the Butt and there I managed to almost eliminate those gaps)

 

  • Like 1

Share this post


Link to post
Share on other sites
6 hours ago, Gadgetman! said:

You may be able to reduce the gaps in her wings by trimming the tab and the matching surfaces around the tab. 

(I've been putzing around with Roland the Pain in the Butt and there I managed to almost eliminate those gaps)

 

 

I already did that on practically every joint on the model :p. In the case of one of the wings, it didn't quite align due to casting and was too thick to heat bend a little. I'm happy to fill the gap on her right wing. The left wing shouldn't even need it.

 

As for Roland.....!

 

What goes in that socket on the left hand side of his body above his belt? I honestly had a few missing pieces and contacted their customer service. Also glue the sword on his back after the shoulder plates. I made the mistake of gluing it on first and it then became very difficult t manoeuvre his left shoulder plate into place. In fact it was dropped on the floor twice and the second time it took me about 2 days to find it again. Because of the placement of the sword I had to snip off the stub and just glue it straight on top of the socket (it was glued on almost immediately after being rediscovered for the second time).

 

Having only one foot as a contact point with the base makes him overbalance and fall backwards until at least one wing is added to counterbalance it. I have yet to attach the left wing to the gryphon because I'm waiting for whatever that piece on the left hand side of the rider's body is before I put a bloody great big wing in the way which would make getting at that socket rather difficult.

 

And yes, Roland's Gryphon is going to need some putty around the joint at the middle of it's body (and one of the knees). Be very careful attaching the reigns. The same goes for the handle thing on the front of the saddle that his hand grips. Because of the length of the stubs you can't just glue the hand in place then glue the body in place because you won't be able to get the left arm on to the left hand. You need to glue the hand into the arm then, as the glue sets, lower the body and arm into position and manipulate the joint until the handle lines up with it's sockets. Then let the glue dry. Make sure it's then handle sockets and not the sockets for the reigns. The reign sockets might need to be enlarged ever so slightly with a drill or modelling knife before the reigns can be attached (which should be done after getting him in the saddle).

 

The plug on the lance arm needs a little carving if you want the standard pole to be able to fit behind the wing correctly. The wing has a slight socket in it for the lance to rest in so use this for dry fitting the lance and calculating arm & wrist angles. My advice is to glue the wrist first as perfectly as possible then mess around with the elbow joint to get the perfect arm angle. Essentially the square plug needs to be carved into something like a rhomboid (or squashed diamond shape) as the default fit would involve the butt of the lance going down through the middle of the wing socket.

Edited by Balgin Stondraeg
  • Like 2

Share this post


Link to post
Share on other sites

Good luck with the assembly, and thanks for posting photos and comments about the assembly!

 

I'll cut above the vent / sprue connection with a sprue cutter, then file it down. I'm quite happy with the Army Painter sprue cutter. It's smaller than pliers, so fits sprues better.

 

fwiw, I've used weaker glues, like rubber cement and even white glue, for resin and plastics. (Museum Wax is a weak bond, if you need to regularly swap weapons on an army model on a movement tray.)

  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Orlando_the_Technicoloured
      https://www.kickstarter.com/projects/cmon/starcadia-quest/description
       
      Main Game ($80)

       
      Expansion Box ($40, so $120 total)

       
      We will ship your rewards at our cost to our international hubs. Depending on where in the world you are, we will either ship to you from our hub in the UK (EU backers), China (Asia Pacific backers), Singapore (Singaporean backers), Canada (Canadian backers), Australia (Australia and New Zealand backers) or Atlanta (USA and the rest of the world). Following is a list of rough estimates for shipping a standard game package (4kg volumetric weight). Keep in mind these are just estimates, and costs may rise based on weight increases from unlocked stretch goals and any optional buys you choose.
      USA: $10-$20 to most states. $50 to Alaska, Hawaii, and Puerto Rico.  CANADA: $15-$30 to most cities.  LATIN AMERICA: $70-$80 to most countries.  ASIA: $10 to China, Hong Kong, and Singapore. $35 to most other countries (we can’t predict an estimate cost to Malaysia). OCEANIA: $20-$45 to Australia. $40 to New Zealand.  AFRICA: $95 to most countries.  EUROPE: $20-$30 to most countries.   • $35 to Norway, Switzerland, Finland, Estonia, and Latvia.   • $50 to Bosnia/Herzegowina, Croatia, and Iceland.   • $70-$80 to Israel, Liechtenstein, and Serbia.  • $90 to Belarus. Unfortunately, different import laws and customs have made it impossible for CMON to ship games to certain specific countries.
      *WE DO NOT SHIP TO:* Russia, Ukraine, Kazakhstan and Afghanistan.
      Basically a Tweaked version of Arcadia Quest designed to run faster and be easier to set up, with Sci-Fi-ification
       
      Dicetower preview video
       
      https://youtu.be/OIBNBe3HPXc
       
      Rulebook work in progress
       
      https://youtu.be/OIBNBe3HPXc
    • By SamuraiJack
      https://www.kickstarter.com/projects/awakenrealms/the-edge-dawnfall-v16?ref=discovery
       
       
      About
      The Edge: Dawnfall is new miniature Board Game by Awaken Realms for 1-4 players. It was created by Michał Oracz (man behind 13 years of Neuroshima Hex and recent hit Cry Havoc) and it brings next level of competitive gameplay to the table. Fresh, exciting, pure and rewarding.
      It’s a living organism with a very passionate community. It’s thousands of hours of development, hundreds of unique art pieces, over hundreds of pages of rich and unique campaigns, 7 extremely asymmetric and unique factions and finally and most importantly a fast, dynamic and very exciting skirmish game with tons of cinematic skills and turn the tide moments.
      This is a second Edge the Boadgame Kicstarter, a reprint of our naive 2016 kickstarter promise of an unreasonably high amount of content that not only we still managed to reach, but even overdeliver. It’s our biggest and most ambitious project yet, it’s our favorite child, our blood tears and sweat. It’s a Beast!
       
    • By Balgin Stondraeg
      Remember this thread?
       
      You know, the Yedharo/GT project that was cancelled and they said they'd reluanch it?
       
      Well they relaunched it.
       
      There's a lot less units this time and far more characters (some of whom appear to have been inspired by the Atlantis Dwarfs or are attempting to copy their success but with a Yedharo/GT spin on it).
       
      I might jump in for a small handful of character models but I won't go in big on this one. Then again why would dwarfs go big? They're small. It's one of their defining features :).
       
      'cause Atlantis did dwarven women with shaved sides and some goat riders......
       

       
      He's baaaaack!
       

       
      She got off the goat
       

       
      Hammer Man is back again
       

       
      Apparently she's really "Busty"
       

       
      At least the leaping Trollslayer is back again :)
       

       
      Mr Ugly Sword is back again (don't know why).
       

       
      I like this new hammer man
       

       
      The ugly rectangular shield unit with hammers is back (the only returning unit).
      They really should've fixed those shields and the "3rd edition/Dragonpunk helmets".
       

       
      The Bloodbowl team is back as well (obviously).
       

    • By Sylverthorne
      So.. I fell over this. It's... well, go look for yourselves; 
      https://www.kickstarter.com/projects/159974695/badbandana-6-pizza-dragons 
       
      ... pizza and dragons. Where have I seen this notion before..? I can't quite... >.>  
    • By Smokestack
      These are the guys that did the Hot and Dangerous Kickstarter. Starts May 15th.
       
      werewolves, musketeers... ahhh I don’t think I can resist this one...
       
      Anno Domini 1666 is a swashbuckling board game of intrigue and mystery, set in alternative reality 17th century Vienna. Two players take command of opposing factions of rogues and heroes carrying out clandestine missions as determined by scenarios. The game is played with miniatures on game boards, using cards rather than dice. Fight with the best fencers in the world. Expect conspiracies, bribery and seduction. Stand against demons and dark magic. Lead yout faction into victory!
       


  • Who's Online   25 Members, 3 Anonymous, 32 Guests (See full list)

×
×
  • Create New...