Jump to content
Sign in to follow this  
SparrowMarie

Wire Clippers

Recommended Posts

I have some minis I want to pin (or attempt to, have never done it before). I have wire, tons of paper clips, and am going to acquire some brass rod soon. But my question is about the clippers. I know I shouldn't use my sprue cutters for most things beyond plastics, resin, and other things like those. 

 

So my question is what kind of clippers (cutters?) Do I need to cut the metal bits down to size? I don't want to ruin my good clippers by cutting something too hard. I saw some in the jewelry section at Michael's but wasn't sure they'd hold up in the long run since it said it cuts soft wire and thread.

  • Like 1

Share this post


Link to post
Share on other sites

Any sort of diagonal cutters from the hardware store should work fine on most wires. For that matter, if you have the usual sort of needle-nose pliers, there's a pretty good chance the included wire cutter will work just fine.

 

If you want to use music wire (which is hardened steel and which is really overkill for pinning), you'll need something like lineman's pliers. Hardened wires will notch the jaws of most diagonal cutters.

  • Like 2
  • Thanks 1

Share this post


Link to post
Share on other sites

I use hardened diagonal pliers for cutting paperclips, and only use my nice flush cutters for sprues. My pin cutting pliers are smaller than the one shown in the wiki link though. Had them for at least 18 years. It's a little beat up but never fails to cut pinning wire. I also have a dented flush cutter that I use to cut brass rod. If I use the diagonal pliers on thin brass rod, it sometimes bends the rod. 

 

I use three cutters for different things:

1. diagonal pliers to cut hard wire like paperclips

2. old dented flush cutters to cut soft brass rods

3. sharp newer flush cutters for sprues

  • Thanks 1

Share this post


Link to post
Share on other sites
18 hours ago, SparrowMarie said:

I have some minis I want to pin (or attempt to, have never done it before). I have wire, tons of paper clips, and am going to acquire some brass rod soon. But my question is about the clippers. I know I shouldn't use my sprue cutters for most things beyond plastics, resin, and other things like those. 

 

So my question is what kind of clippers (cutters?) Do I need to cut the metal bits down to size? I don't want to ruin my good clippers by cutting something too hard. I saw some in the jewelry section at Michael's but wasn't sure they'd hold up in the long run since it said it cuts soft wire and thread.

 You are right about the jewelry clippers. They are only good for soft metals.

  • Thanks 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By haldir
      So I've always have had problems pinning a round object, more or less trying to get the pin vise/drill into the round part of the piece. In this instance, the round part is the hand of the river troll 14008 (Warlord line). The wrist has a perfect indentation for the "ball" of the hand. With having to travel to play & such & of course actual gameplay I don't trust superglue alone.
       
      Any tips?
    • By FireImp
      So I was drilling a plastic figure last night, and realized part of my issue with drilling is my hands are stiffening up, and it won’t be too much longer before arthritis becomes an issue. I was looking at Dremel attachements, and came across small rotary engravers, which also might work. Does anyone here have any experience with ways to drill that don’t involve pin drills? Has anyone tried the rotary engravers? If your hands aren’t nimble, how do you drill?
    • By FireImp
      How do you handle painting those tiny bits like arms and shields before gluing a figure together? I’ve got one arm drilled and mounted on a piece of paper clip that worked pretty well, but I’m looking at my next mini and wondering if there isn’t a better way...or at least one that doesn’t involve drilling, which I’m not very good at.
    • By Nightwing
      Here are 4 twisted wire trees I made. Three of them use moss from a craft store package, one used Woodland Scenics foliage. They all use Vallejo Earth Texture, Woodland Scenics scrubery, and Army Painter Lowland Shrubs. 
       
       




       
      Here is is an average wizard under a tree for size reference: 
       

    • By Pingo
      I recently got the set 06173: Shadow Sisters. It consists of four of the figure on the left and five of the one on the right.

       
      Only,  that’s not quite what they look like. The figure on the right has an extra cape piece.
       
      The figure on the left has lacing up the middle seam of her cape. The figure on the right’s cape has a similar seam right at its edge and there is a separate cape piece (not depicted) of another half of the cape.
       
      There is a little nubbin to affix the cape which goes into a little socket in her left shoulder. It looks like it could be a precarious pinning job.
       
      The cape piece looks like it could possibly be glued in from a variety of angles, from matching the seam of the integrated cape to flying dramatically back. I tried to find out the official position, only to find that in the store photo above the second cape piece is not included.
       
      May I ask, what was the original artist’s intent for the second cape piece?
  • Who's Online   14 Members, 1 Anonymous, 64 Guests (See full list)

×
×
  • Create New...