Jump to content

Welcome to the Workshop! (Picture Intense)


Recommended Posts

So my hobby space was getting cluttered; I had multiple sizes of paint/hobby bottles. Now, I could buy a pre-made organizer, but what would be the fun in that! Ladies and gentlemen, boys and girls - lets step into the workshop and remedy this issue...

 

Step One: Come up with the battle plan.

This space here needs to be hold an organizer. As you can see, I have larger bottles (Vallejo specials/Daler Rowney Inks), Tamiya Clears, GW pots, and the standard dropper bottle fair.

 

20180922_114721.thumb.jpg.f307a850240cba93b65534151adc31b4.jpg

 

Step Two: Find some scrap material to work with.

I grabbed a piece of 3/4" Oak plywood I had lying around and took some measurements to see if it was a good candidate.

 

20180922_115010.thumb.jpg.a899a6583f1c4bf8e5e9132ab598abf3.jpg

 

Step Three: Get to work!

I tossed in on my cross-cut sled on the tablesaw, marked the line (and always mark your waste/outside cut line to prevent confusion) and cut it down to size.

 

20180922_115511.thumb.jpg.ae30f3294d5062bbea72342fe481dce1.jpg

 

This humble 2x4 will serve as the sides and shelf frames for the storage unit...

20180922_130045.thumb.jpg.0654df4d77aeb8ec51e62de57b3d1ec5.jpg

 

I take it to the jointer to get a flat face and edge and we clean up the other side on the planer and the tablesaw.

20180922_130422.thumb.jpg.65e60c79df65d67faaff8492b411ca90.jpg

 

Then to the bandsaw to resaw the board. Resawing is cutting a board's thickness in half.

20180922_130819.thumb.jpg.2ac24d0c2b19939d89253d83bb95649c.jpg

 

Ta-da! Two halves ready to be used!

20180922_131011.thumb.jpg.6ece561d3d42fa2c2257274ab927ec91.jpg

 

Here are a few bottles to take as a means of reference to measure the shelf sizes needed.

20180922_131941.thumb.jpg.5fee77283b2a54d1ab35f4fc22dd6d00.jpg

 

Getting a general idea of the shelf layout.

20180922_133643.thumb.jpg.30c2e2c27fadd4b6d4451cda0b49602c.jpg

 

Gluing up and tacking the shelves in place, adding in the trim to the front of the shelves to match the sides...

20180922_155546.thumb.jpg.d41bc74518109562616f81ada18dd57a.jpg

 

All glued up and ready for sanding and a final seal coat!

20180922_162431.thumb.jpg.f4e956cbb3259ab26f47e3888db59908.jpg

 

Sanded and a couple coats of Danish Oil later we have our hobby organizer!

20180922_170228.thumb.jpg.5ea2068b948af12d4ac698ecb68e4785.jpg

 

Have you constructed something for your hobby battlestations or otherwise? Foam? 3D printed? Welded? Any other DIY'er that have taken the plunge into focusing that into their painting hobby? Super-sized something from IKEA? Let me know!

  • Like 10
Link to post
Share on other sites
  • Replies 1
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

The only thing like this that I've done is some simple shelves for games and minis. Some were made of 1" x 12" pine and some just cheap plywood. In my current house I did 8' x 13" x 6' high plywood shelves for all my collection. Pretty crude but got the job done. Getting scarily close to filling up and I haven't migrated everything from my old house yet.

 

I have a paint rack similar to this.

Image result for mdf paint rack

and it came with extra pieces. I've already filled it up and need more and I'm considering using the extra pieces and making more out of some 3mm mdf sheets I have. Just not sure I can make a decent job of it with the tools at hand.

  • Like 8
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Darcstaar
      I only saw one thread about crackle paste when I searched these forums.
       
      So, I’m going to share how it’s going for me.
       
      I started with washed and dried 1” and 2” Reaper Bases.
       
      I put this garbage on a 2 inch base first.

      Don’t buy it.  I got it at Hobby Lobby at the time because they were out of Folk Art.
       
      To be clear, this is Crackle Medium.
      It is meant to be painted on a primed or rough surface I guess, and painted thin. I put it on kind of thick.  It didn’t crackle at all!
       
      So, I got a tub of this stuff on Amazon.

      The directions state “put over a thin layer of PVA glue.”  Pfft, who has time for that extra step?
       
      Here is the result on a washed but otherwise un prepped set of bases.

      1 inch
       

      2 inch.
       
      Lousy!
      So, the surface needs something for crackle paste to work right.
       

      This is a 1” base with a thin layer of PVA glue.
       

      This is a 1” base with just hitting it with 220 grit sandpaper and washing it again.
       
      I also used the 2” base with dried crackle medium on it.  Not pictured.

      This is a 2” base covered in black brush on primer.

      Here is the result on the 2” base over dried crackle medium.  It was hard to get the stuff into a uniform layer, as the medium created a very hydrophobic surface, so the paste slides around too easy.
    • By BLZeebub
      So after too many years of painting with my bottles just in boxes or standing around on my shelf of shame or in various drawers, I have finally at much cost of labor made paint organizers!  BEHOLD!  I made these to hold up to 204 Reaper dropper sized bottles (Army Painter and Vallejo fit too).  They aren't the only ones I use by any means, but they're the bulk of my paint collection.
       
      Wasn't the hardest thing in the world, but honestly I might try another method if I do this again.  Right now the units are loose, probably going to lean them on the wall--eventually I would put supports on the backs so they can stand up at an angle (think picture frames).  The insane super duper bonus feature is that I can put the two together and transport, or more importantly, SHAKE all my paints at once!  The main purpose was organization though and being able to see each of my paints and, when I've organized and sorted them, see the spectrum at a glance rather than digging through a drawer as I have been doing.  For the chromophiles out there I'll post pics when they're sorted and in their proper places.
       
      To make them, I sized the bottles and figured out the hole size and spacing (bottles are about 1" diameter, I used a 1 1/8" hole saw (paddle bit blew out the back side) and drilled 102 holes (sandwiched the 3/4" boards together).  It took hours as my drills' batteries kept dying and the saw lost its good edge by the 60th holes or so.  I used the "holes" I drilled out as supports (had to chisel the middle supports in half) between the silver parts and the 5mm (yes, civilized world, in the US we know how to use proper/metric, and certain sizes of wood are specified in metric!) plywood base (black, not really visible).  I carefully glued and screwed these together.  Decided to use up some spray paint I had lying around.  Enjoy and be inspired!

    • By Ekaterina
      Hi!! my name is Katerina and I'm new to painting miniatures, I begun 
      with a miniature from NonSenseminiatures, the Barbarian, I buyed the 
      54mm because it's bigger and maybe easier to paint.
      I asked some help to NonSense and he already made a base coat for me, I 
      would like to get some help for painting because I see too much 
      information and don't know were begin.
      I already make painting but totally different
      Also he gave for me a discount code Katerina10%, because he will sell my 
      paints also!!!
       




       
    • By Rob Dean
      I expect that most of us are painting as a break from busy lives. I’m interested in knowing how much painting time people find, regular or binges, time of day, and if
      you’ve had any success in finding more...
       
      Personally, I tend to paint in blocks of several hours on weekend days when I
      can, which isn’t that often. I’ve long tracked painting completions (since ‘95 continuously now), but not how often or how long I spent painting. I started a habit tracker this month to see, inspired by my brother who set a goal of 30 minutes a day. So far it’s been an unimpressive 5 of 11 days. At home I do most of the painting between breakfast and lunch, which is often quiet time on the weekends because my SO is able to sleep in and I am not. 
       
      My best found time technique is to have a second paint set at work, and paint at lunch if there isn’t a work crisis. 
    • By Talae
      This is a look at the disaster of what the space currently looks like (you have been warned):
       


       
      Not pictured is the rather large corner desk, the Detolf shelves on the other side of the room, and the terrain taking up the closet.
       
      Here is the Ikea purchase from today that will help substantially with organization. (Two 3x3 Kallax shelves, three sets of drawers to fill three of the 18 cubes, two 6-drawer Alex drawers, and a countertop to go on top of the drawers)
       

       
      I may eventually get another 3x3 to stack on one or both of the others, and also may eventually get some doors and/or drawers for the Kallax shelves, but not yet. Ikea is a little over an hour away, so this combined with lunch and dessert was a decent amount of a day trip with the family.
       
      Wish me luck!
  • Who's Online   27 Members, 1 Anonymous, 30 Guests (See full list)

×
×
  • Create New...