Recently Browsing 0 members
No registered users viewing this page.
So for those of you who are experts on this kind of thing, I have a question that's bugging me a fair bit, and hoping to get a few answers. Started using my Windsor and Newton Series 7 size 0 brush, which had pretty much a perfect tip to it when I bought it... I have a few hours with this now, maybe 3, and it's been doing this since around the ten minutes in mark....
^That's how it looks right after I take it out of my paint water, and then blot the excess water off.... Well, about 95% of the time anyways, but still.
^This is what it does just lying on my desk within 2-3 minutes after the fact -well, about half the time anyways, sometimes it waits until paint goes on...
^For example of how the bristles go in odd directions and won't hold a point, this is right after a quick dip into one of the washes I'm working with at the moment, although usually the split is most of the way through the bristles.
For reference, this is how it looked brand new (sadly, I don't have any shots of it out of the tube and with the protector off before initial use)
So, a few questions come to mind:
- What is happening with this?
- Can it be fixed?
- What can be done to prevent it from happening again? Kind of... Okay, I won't lie, I'm rather annoyed (to use a forum appropriate wording) at a $25 CAD brush behaving in a manner none of my other brushes have (well, until they've seen a LOT of use)
Thanks in advance!
So, I'm finally thinking it may be time to break down and purchase a Dremel (or similar tool). However, I have no idea what to look for in such a tool and was hoping that some of you could help me out. I'm not likely to be using the heck out of the thing by any means. My main intended uses for it are going to likely be to help with mold lines (I've found that with the metal figs I still have trouble getting rid of some mold lines with my files and I'm hesitant to use the X-Acto knife for a couple of reasons. I may also occasionally use it for drilling pin holes on particularly stubborn pieces (my pin vice sometimes gets cranky with me making pinning a chore a lot of the time). Finally, I can see me occasionally using it to make mods/conversions to minis. Nothing really spectacular at this point, but possibly things like turning a creature into a zombie variant by drilling out some of the skin and then molding in some flesh with green stuff, etc.
Obviously as time goes on I might expand a bit, but for now, not looking for anything too fancy (or at least I don't think I am). I don't mind spending money to get a good product, but also don't feel the need to spend (for example) $150 when a $50 version would do just as nicely.
As always, thanks in advance for any help!
My wife got me a nice set of brushes for Christmas. Aside from two she got me a few years ago, I have never had nice brushes before.
I have never properly learned how to care for brushes, but would like to do that now.
What resources are out there? What should I buy?
So, I've just started recently and after much research, I figured out that I'd need a few 'throw' away brushes for dry brushing, gluing, etc, and then at least one decent brush. I picked up a cheap variety pack of brushes from walmart for $3 and a winsor newton #1 . My expectations on the WN were...not met. It doesn't hold a tip well at all, the moment I touch it to anything, it starts to splay out. In fact, the cheap brushes from Walmart seem to do better.
Bad brush possible? Or bad technique? Am I expecting too much? I've definitely not let paint into or dry in the ferule, I rinse often, and i tend to twirl the edge of the tip to bring it to a point on the pallet.
My brother was cutting up cedar limbs to use for a project for his wife. I figured I might as well grab a few just in case I might could turn them into bases or platforms for miniatures. I have several sizes and several heights, but when I started looking I was not finding much on integrating something like this into a base. Lots of things for already prepared woods, but not many ideas on fresher wood. Now, most of these limbs were dropped from trees, so, not exactly full of sap:
I am thinking I would need sealer but wasn't sure how that would interact when trying to get a miniature to adhere, or should I strictly use the taller ones as a plinth of some kind that the completed miniature sits on?
Thoughts? Ideas? Practical experience?
Also need to find the best way to handle the bark (leave it, clear it, etc.).
Who's Online 31 Members, 1 Anonymous, 34 Guests (See full list)
- Disciple of Sakura
- Knight of the Dinner Table
- Cranky Dog
- Chris Palmer
- Rhydur Meith