Recently Browsing 0 members
No registered users viewing this page.
StackaRack is a customisable plastic rack for miniature paints, designed to hold pots or bottles from any of the major manufacturers.
Paint collections have a way of growing organically, and most of the current paint rack solutions out there are fixed to specific configurations, and made for a specific type of paint pot. If you're like me, and collect multiple brands of paint, that can make organising them a little frustrating, and so we thought we would try to fix that.
StackaRack was designed to hold any of the major miniature paint ranges - from the dropper bottles used by Vallejo and Army Painter, to the tall pots from the likes of Privateer and Reaper (and GW's old range), and the current stubby Citadel pots. The injection moulded plastic parts will fit together with plastic clips, allowing you to build it how you like, and disassemble and reconfigure it as needed.
Check out the project live on Kickstarter here: https://www.kickstarter.com/projects/spiralarmstudios/stackarack?ref=acpi8t
I'd never felt I had an artistic bone in my body until I started painting minis. Well, now, I decided I'm going to try my hand at 2D art.
I am following along Bob Ross videos on YouTube. I will note, and this is probably very important, that I am using acrylic paint and not oils. I did not want to spend oil paint prices since this is a new thing for me.
These are the two I've done:
Day 1: I learned a lot, I needed to do something with my paint to extend the drying time. This would have helped with the blending. Overall, happy with it excepting the house.
2: I used some slow dry medium mixed into the paint today. Not sure if it was not mixed well enough or I didn't use enough but it only gave me like 5 minutes or less of extra working time. If anyone has any suggestions for how to use slow dry medium, please, let me know. I'm using heavy bodied acrylic tube paints.
I followed along until the end and I decided to add some darker blue and green. I think that helped a lot.
Another note, need to find sturdier paper. While this is holding up it likes to curl slightly while drying. The second one is taped to the desk on the back to try to minimize that problem. I am currently using a mixed media paper.
So how do I paint something with a marble effect? I have a sepulcher or sarcophagus, primed light grey, and I want to paint it like it was made from marble. Any ideas or tricks? Colors? Anything? Bueller?
If it helps, its the one from the Horror subset of the Bones 4 Kickstarter.
Hi all. I recently acquired a few bookshelves which have become the new home for my miniatures and gaming materials. The shelves came with a good out section in the middle and I think it might be the perfect place for a photo set-up.
I currently use a white sheet of cardstock as an infinite backdrop with the two 1520 lumens daylight LEDs that I use for painting and a light source from either side. It works well enough but it's just inconvenient enough to set up that I'm looking for change.
I figure now is a great time for an upgrade.
I'm thinking I've never really worked with lighting and anything electrical so I think that's mostly where I need guidance. I'm hoping I can fasten some LED strips to the walls and top and then run the wiring out that hole that was conveniently cut out of the back.
Other than that, I'm thinking I can just tape in a sheet of white poster paper and swap it out if it starts to get too beat up. If I'm really lucky, there will still be room inside to store my camera bag.
I also am wondering if some kind of diffusion will be necessary or if the LED strips will have a general enough soft light on their own.
I also have to be mindful of wall placement because the arms of the "door" brush against the wall about midway when closed.
For the curious, the shelf is about 14" deep, 13" high, and 25" across. And the open "door" is about 14"
Thoughts/advice of any kind are welcome!
As a side note, if the LEDs work well here, Iight try swapping out the old lights in the display cabinets up top. They are a gross old orange color.
Today I wanted to show off some cheap 54mm Vikings that I painted up as Frost Giants.
I made these guys close to a year ago, and they were among some of the first larger sized minis I had worked on, so they're a little rough, and that's before looking at the quality of model, but if someone else is in need of a lot of giants like I was, then this might be useful to them!
So these guys are from Tehnolog, a Russian miniatures company that I know very little about. The minis are made out of a soft plastic like novelty toys you can buy with tickets at an arcade. They also have abysmal detail.
They're meant for 54mm wargaming, and I believe there's an intended game system that accompanies the line, but my goal was to get some cheap giants for D&D.
They fit nicely on a 2in base, and could probably fit in with the smaller Reaper Bones giants, but they're definitely a little undersized. I remedied this by giving them each a boosted base, with the leader getting two layers. At a glance, they tower over a standard medium sized mini.
The details were rough and there were some ugly mold lines here and there. But they're serviceable. They might work better as a half-giant if you want to use 5e's Huge Frost Giants.
More pictures of each giant below the Spoiler:
Tehnolog also has a few other lines of fantasy-esque minis if you're a fan of cheap minis. I am still considering getting one of their other lines to convert into cheap-o Fire Giants.
What's your favorite obscure miniature substitute?
Who's Online 15 Members, 1 Anonymous, 45 Guests (See full list)