Jump to content

Recommended Posts

I'm not really sure when I'll get to these, but I found a bunch of cheap sheets that I'm going to diy into mats for wargaming. As it is, they're fine (I got green, blue, and brown, and passed on a grey) . But I might sponge on some various paints for waves/ ice (double sided blue sheet) and various greens for the green sheet.

  • Like 3
Link to post
Share on other sites
  • Replies 0
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By haldir
      Ok, so next week I'm gonna be replacing the LCD in my printer finally, but I'm also gonna replace the noisy fan on the very bottom of the printer. I finally found a good shot of the guts from the bottom:
       

       
      Now the fan I ordered a few months ago is definitely not the one I need as it's one of the filter fans. So I'm gonna have to order a fan this week. That is why I'm posting here. What fan is good for this?
       
      I've read where someone has modded theirs to run a 120mm fan, I just wanna do a direct replacement of it. One caution I have is the connections. Does the fan just clip into one of the white connectors or is it one that the wires go into the posts that screw down (like on a Ender 3)?
       
      Funny how now I find this site vs trying to find anything these past few months:
       

      (note the fan wire, it clips into one of the white connectors (yeah!!)
      Any help will be appreciated for this.
    • By MoonglowMinis
      How do you make an octopus laugh?  You give him ten tickles!

      Wanted to show off this little octopus that I sculpted from some leftover green stuff.  I don't have much experience with sculpting other than a few simple embellishments on minis and a couple of snake swarms I made once.  Wanted to try something relatively simple and figured an octopus would be pretty forgiving.
       
      You can see more about how I made this guy and more of my nautical minis in my Dark Tide WIP thread HERE.

       
      I sculpted and painted this guy in two evenings and am happy with hos cute it turned out.  It's not the most accurate, but I'm proud of it.  It definitely has given me greater confidence in my ability to make something out of nothing.
       
      More Photos Beneath the Spoiler:
       
    • By MoonglowMinis
      So for awhile now I've had this goal, nay, this desire, nay, this primal compulsion to build a boat.  It is not enough to have hand drawn maps, or 2D terrain tiles.  I need a fully functioning 3D boat!  Well, maybe not fully functioning.  But I want to build a cool boat!
       
      I've been working on a nautical campaign full of swashbuckling, sailing, and sea monsters for a few years now.  It's my White Whale project.  Always just on the horizon.  It'll happen some day, but in the meantime, I have a million small projects to complete and extend the chase.  One of which is my desire to build a few different sized ships to enliven any possible naval combat.
       
      I actually attempted this about two years ago, just winging it and making some measurements and throwing them at some craft supplies.  I wanted a cheap option that wasn't too difficult to repeat that way I wouldn't be discouraged from making multiple ships.  So I limited it to cheap crafting materials like foamcore, wooden dials, popsicle sticks, and thumbtacks.  And the result wasn't  bad.  Especially for my first attempt at any kind of terrain building.


      It actually turned out rather nice!  To my surprise.  But I got hung up on mast and sail designs and never finished.

      The wood on the deck had 2x1in grid carved into it for easier D&D use.

      and the figurehead was designed to be modular.

      However, overtime the boat collected dust and little scratches.  I should have given it a coat of mod podge or sealant of some kind, but never did.  And eventually it had an unfortunate run in with an injured owl that we took in for a night.

      Here's the little devil himself.
       
      Anyways, I put this project on the back burner for long enough and feel inspired to dive back in.  Especially with a certain Bones ship on the Horizon that I'm still on the fence about getting.  I was doing some browsing on the web and recently found this wonderful little blog complete with loose instructions and a plan from a now defunct wargamming site.  The blog creator had found the old plan and adapted it to build something using most of the same materials I have already stockpiled. 


      There's a few choices that I like better than my first attempt so I think I'm going to use this as some inspiration as I give this boat thing another go.

      My hold up now is still those darn masts.  The original plan above used wood and required drilling out holes for the masts.  The blogger use foam for his ship and found random bits of tubing to house his masts.  I could try to find something random like that, but I was hoping to find something simpler for easy repetition.  And I would also like to keep the masts loose so they can be removed for easy storage, or to swap out the sails.  Any thoughts?

      Any resources, tips, recommendations are very welcome!  I'll post back here with any updates.

    • By Glitterwolf
      Here's what I painted in 2019.
       
       






















    • By Nook
      Greetings all!
      I had a fun idea for a mini that I need for an upcoming game, so I decided to DIY it. So this will be my
      DIY Ochre Jellies 
       
      I’m using white gorilla glue, the kind that foams up, and a bent safety pin. As it begins to dry I moved the “blob” up along the pin to gain some vertical height. The white will be an ok under coating, and I’ll paint it up tomorrow once it finishes drying. I’ll snip the end of the safety pin off before painting too. 
  • Who's Online   20 Members, 3 Anonymous, 33 Guests (See full list)

×
×
  • Create New...