Gadgetman! Posted August 27, 2020 Share Posted August 27, 2020 4 hours ago, Glitterwolf said: Because when I see that something has failed I will use the scraper to clean the FEP, if I use the metal one I forget that it's metal and I have puntured one FEP that way. So I rather use the plastic one and it does a wonderful job. I don't scrape off bits stuck to the FEP until after I've disposed of the failed print and filtered the remaining resin back into the bottle. And the metal scraper is left in the bath where my IPA containers are, and the resin bottle, filters and funnel is in the room where I keep the printer. 5 Quote Link to comment Share on other sites More sharing options...
Illithar Posted August 27, 2020 Share Posted August 27, 2020 'A Gambit of Guns' continues to vex me. It prints great with the new resin, I can see most all of the details except... Now the hammer and sites on the gun are failing. The supports just seem to disintigrate, I have tried to reinforce them but that did not go well. The presupported file is, unfortunately, not a chitubox file and the supports are part of the file and cannot be altered. I will probably try to do my own supports, maybe at a different orientation as well. I could try lowering the lift speed even further, but it's already fairly low at 70mm For the time being though, I have a different file going in my printer while I am at work, hopefully it comes out OK. Right now I'd just like to have a 100% successful print. 5 Quote Link to comment Share on other sites More sharing options...
Standifer Posted August 28, 2020 Share Posted August 28, 2020 10 hours ago, Cygnwulf said: have you seen the guys who have taken 60 grit sandpaper to their plates to fix adhesion issues?" I will be giving that a try. I tend to have adhesion issues even after leveling the bed. 2 Quote Link to comment Share on other sites More sharing options...
Sophie was taken Posted August 28, 2020 Share Posted August 28, 2020 I got my printer today! I have no resin for it yet. 6 1 2 Quote Link to comment Share on other sites More sharing options...
Cygnwulf Posted August 28, 2020 Share Posted August 28, 2020 10 hours ago, Sophie was taken said: I got my printer today! I have no resin for it yet. 1 7 Quote Link to comment Share on other sites More sharing options...
ttuckerman Posted August 28, 2020 Share Posted August 28, 2020 You forgot the tm. 2 2 Quote Link to comment Share on other sites More sharing options...
Glitterwolf Posted August 29, 2020 Share Posted August 29, 2020 RN Estudio on MMF 50% off! 2 Quote Link to comment Share on other sites More sharing options...
haldir Posted August 29, 2020 Share Posted August 29, 2020 1 hour ago, Glitterwolf said: RN Estudio on MMF 50% off! That might even be better then the Patreon discount....hmmmm 1 Quote Link to comment Share on other sites More sharing options...
Sophie was taken Posted August 29, 2020 Share Posted August 29, 2020 I got my resin! What is ethanol and can I use isopropyl instead? 1 Quote Link to comment Share on other sites More sharing options...
Glitterwolf Posted August 29, 2020 Share Posted August 29, 2020 14 minutes ago, Sophie was taken said: I got my resin! What is ethanol and can I use isopropyl instead? You can use those, you can also use denatured alcohol. Alternatives: https://www.youtube.com/watch?v=x1NqdUaSZzY&t=4s https://www.youtube.com/watch?v=DqtkifF3-2I 1 Quote Link to comment Share on other sites More sharing options...
KruleBear Posted August 29, 2020 Share Posted August 29, 2020 3 hours ago, haldir said: 4 hours ago, Glitterwolf said: RN Estudio on MMF 50% off! That might even be better then the Patreon discount....hmmmm I am dumb....when I go there I see them at full price. I would like to get a couple of his fantasy football team minis if half price. 2 Quote Link to comment Share on other sites More sharing options...
Glitterwolf Posted August 29, 2020 Share Posted August 29, 2020 Just now, KruleBear said: I am dumb....when I go there I see them at full price. I would like to get a couple of his fantasy football team minis if half price. When you buy it use the code RN50 as mentioned on the frontpage of MMF. Then it will substract 50% 3 Quote Link to comment Share on other sites More sharing options...
KruleBear Posted August 29, 2020 Share Posted August 29, 2020 5 minutes ago, Glitterwolf said: When you buy it use the code RN50 as mentioned on the frontpage of MMF. Then it will substract 50% Thanks I feel stupid. I looked for it the last few hours. Literally found it two minutes after posting the question above! 2 Quote Link to comment Share on other sites More sharing options...
Glitterwolf Posted August 29, 2020 Share Posted August 29, 2020 8 minutes ago, KruleBear said: Thanks I feel stupid. I looked for it the last few hours. Literally found it two minutes after posting the question above! I've had stuff like that happen to me a few times. Sometimes we just overlook something. No problem.. There are some nice designs in there. I already bought the Manticore a month ago. Now I wished I had wait. 2 Quote Link to comment Share on other sites More sharing options...
haldir Posted August 29, 2020 Share Posted August 29, 2020 Allot of times the % off sales are on the front page of mmf. You just gotta scroll the entire page to find all of them. 4 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.