Jump to content
Sign in to follow this  
Anne

3D Printing General Discussion (merged)

Recommended Posts

More previews from Epic miniatures for the upcoming set.

Still about 6 miniatures that are in development and not revealed yet.

 

image.png.92130c1709cd2d123ee5094dbc23e5e7.pngimage.png.beb44c1a31b0dd989f14b4a80f5de6e9.pngimage.png.8ecde016a8e429a6250117e6492d20c3.pngimage.png.d12633f4835df86bab2722cfaa94af62.png

image.png.9c80ac3db6d71e454caeb21db380d6ae.pngimage.png.e6ef171f9de158288d723d56dcffe1a8.png

image.png.324d46de24fcfe17f2610ed446461ff0.png

 

  • Like 6

Share this post


Link to post
Share on other sites

I use Prusa Slic3r, but i have a Prusa mini so...

 

It does support other printer manufacturers as well, though there is not yet a CR-6 profile.  I'd start with the Ender 3 profile and make adjustments to the bed size, feed rate, etc. to more closely match the profile in Creality slicer.

  • Like 2

Share this post


Link to post
Share on other sites
4 hours ago, Glitterwolf said:

More previews from Epic miniatures for the upcoming set.

Still about 6 miniatures that are in development and not revealed yet.

 

image.png.92130c1709cd2d123ee5094dbc23e5e7.pngimage.png.beb44c1a31b0dd989f14b4a80f5de6e9.pngimage.png.8ecde016a8e429a6250117e6492d20c3.pngimage.png.d12633f4835df86bab2722cfaa94af62.png

image.png.9c80ac3db6d71e454caeb21db380d6ae.pngimage.png.e6ef171f9de158288d723d56dcffe1a8.png

image.png.324d46de24fcfe17f2610ed446461ff0.png

 

 

4g1on7.jpg

 

Icewind Dale adventure!!!

  • Like 2
  • Haha 3

Share this post


Link to post
Share on other sites
On 9/22/2020 at 11:30 AM, PaganMegan said:

I may need to slice that second bear again.

 

The printer got to the same spot, then stopped this time.

 

I hit Resume, and it started again, but that makes me suspicious.

 

Sliced with the Creality slicer.

Printed on her third try - then broke off at the ankles  when she tries to take it off the bed.

At that exact same place.

 

And the break was smooth.

 

On the other hand, two dabs of super glue and done.

 

The Auld Grump

 

 

  • Like 8

Share this post


Link to post
Share on other sites
9 hours ago, TheAuldGrump said:

Printed on her third try - then broke off at the ankles  when she tries to take it off the bed.

At that exact same place.

 

And the break was smooth.

 

On the other hand, two dabs of super glue and done.

 

The Auld Grump

 

 

 

I've had some resin prints where the delicate bits broke off during support removal, If I can glue it and then paint it so it's not noticable I consider it a succes.

 

You could try to put the bear in an angle?

Or does this cause problems with FDM?

 

Edited by Glitterwolf
  • Like 2

Share this post


Link to post
Share on other sites

Run the STL through a fixer, such as the Formare Online STL Repair. 

It's possible that there's something wrong with the file...   

 

Also, if the slicer supports it, zoom in and 'step' through the layers to look forr errors. 

 

  • Like 3

Share this post


Link to post
Share on other sites
11 hours ago, Gadgetman! said:

Run the STL through a fixer, such as the Formare Online STL Repair. 

It's possible that there's something wrong with the file...   

 

Also, if the slicer supports it, zoom in and 'step' through the layers to look forr errors. 

 

Zooming in, one of the layers was hollow, just the outside.

 

Clicking Fix in Chitu fixed it!

 

  • Like 3

Share this post


Link to post
Share on other sites
On 9/23/2020 at 7:43 PM, TheAuldGrump said:

Printed on her third try - then broke off at the ankles  when she tries to take it off the bed.

At that exact same place.

 

And the break was smooth.

 

On the other hand, two dabs of super glue and done.

 

The Auld Grump

 

 

Ooookaaaayyyy... Just noticed that the Creality Slicer thought it would take an hour and six minutes to print the bear....

 

Yep, something was screwed up.

 

The Auld Grump

  • Like 1

Share this post


Link to post
Share on other sites
1 hour ago, Humansquish said:

Anyone know of a slicer that will save in .phz that isn't Chitubox?

 

Lychee slicer will.

  • Like 1

Share this post


Link to post
Share on other sites
2 hours ago, Humansquish said:

Anyone know of a slicer that will save in .phz that isn't Chitubox?

 

for a Photon?

 

If so, Formware will do it. But that's a commercial package($150 or so).

There's a 30 day test period, though.

 

  • Like 1

Share this post


Link to post
Share on other sites

Hey folks, I asked for a 3D printing forum so we can break topics out like Printer settings, resin reviews, show off your prints, etc..  please feel free to stretch your wings in the new space.. 

  • Like 5
  • Thanks 5

Share this post


Link to post
Share on other sites
8 hours ago, Gadgetman! said:

 

for a Photon?

 

If so, Formware will do it. But that's a commercial package($150 or so).

There's a 30 day test period, though.

 

For a Phrozen Sonic Mini. I'll look into Lychee. I tried Z-suite, which the little I've played with it I like, but it doesn't save to the right format for my printer to recognize.

  • Like 3

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...