Fishman Priest Pope Bulbloba by Glitterwolf

[Glitterwolf]

This is Pope Bulbloba from the Death Tide Jurakin set from Artisan Guild.

Printed on the Elegoo Mars.

 

Wielding his magical weapon.

 

Part of the Beneath the Waves Project.

https://forum.reapermini.com/index.php?/topic/88958-beneath-the-waves-by-glitterwolf/&tab=comments#comment-1896746

 

 

Edited August 31, 2020 by Glitterwolf

[Coydt]

You have some great figures there.  You do a great job on the basing.  The water effect is great.

[darkreaper00]

His human flesh coloration makes me uncomfortable.  Good job!

[Glitterwolf]

7 hours ago, Coydt said:

You have some great figures there.  You do a great job on the basing.  The water effect is great.

 

Thank you, I used a simple trick actually.

Painted the base in a sand brown tone using three different tones, then used Warcolour Translucent Blue and watered that down even more.

That way you get the idea that there is shallow water on that sandy base.

 

7 hours ago, darkreaper00 said:

His human flesh coloration makes me uncomfortable.  Good job!

 

Thanks!

Mission accomplished!

Edited August 10, 2020 by Glitterwolf

[Iridil]

Yikes - good thing I looked at this during the morning... he's the stuff of nightmares! Nice job.

[Glitterwolf]

2 hours ago, Iridil said:

Yikes - good thing I looked at this during the morning... he's the stuff of nightmares! Nice job.

 

Thank you!

He does look a bit evil doesn't he?

[AussieAusborn]

That's a good looking fishman! I especially love the work you did on the weapon and the glowing dangling bit.

[supervike]

Wonderful job!

 

Out of curiosity, how long does a figure like that take to print out?

[Glitterwolf]

On 8/26/2020 at 12:47 AM, AussieAusborn said:

That's a good looking fishman! I especially love the work you did on the weapon and the glowing dangling bit.

 

Thank you!

I used Vallejo Fluo Yellow and two Scale 75 green colours for that.

 

On 8/26/2020 at 2:51 AM, supervike said:

Wonderful job!

 

Out of curiosity, how long does a figure like that take to print out?

 

Thanks.

 

Depending on the angle you use somewhere between 2 and 4 hours.

 

It takes longer if you print it upright instead of laying down, but it does leave less marks from the supports.

 

Edited August 31, 2020 by Glitterwolf

[Samedi]

I never really saw the barnacles in the WIP...

 

Love the result!

[Glitterwolf]

15 hours ago, Samedi said:

I never really saw the barnacles in the WIP...

 

Love the result!

 

Thank you!

[Rigel]

You know I love a good fishfella, and this is absolutely fantastic! Agreed that the flesh tones really give it that uncanny-valley vibe. (Uncanny mid-oceanic trench?)

[Glitterwolf]

On 9/3/2020 at 12:35 AM, Rigel said:

You know I love a good fishfella, and this is absolutely fantastic! Agreed that the flesh tones really give it that uncanny-valley vibe. (Uncanny mid-oceanic trench?)

 

Thank you!

I always love your fishmen and deep ones, so I'm glad you approve of mine.

 

Since you like fishmen, have you seen his girlfriend?

https://forum.reapermini.com/index.php?/topic/92473-telaxia-tidal-beauty-by-glitterwolf/

Edited September 4, 2020 by Glitterwolf