Jump to content

Recommended Posts

Post your successful prints here, we all like to see the pretty minis.

 

Here are a few I got recently from RN Estudio off of MMF. Sorry for the crappy pic but I don't want to retake them.

 

RNEstudios2.thumb.jpg.fa47514d91f32fd884a067711587460d.jpg

  • Like 7

Share this post


Link to post
Share on other sites

Well using MS 3D builder I managed to cut the one model of the monuments of Axum and got it to print even though the creality slicer didn't want to rotate it to exactly upright.  I was wondering why one side showed no detail until I realized that it was covered by a support.  Anyhow it printed nicely without any kind of base.    I should be able to print a larger version in two parts and also a broken one.

 

Cut_stellae.thumb.jpg.d7611f02d765d34fe5159bc05a8a7eab.jpg

Edited by lowlylowlycook
  • Like 6

Share this post


Link to post
Share on other sites

2nd Dynasty's starfighters thats 2 of the 3 cores the kit makes a number of clones like the Awing and X wing here.  The kit will also make a couple of versions of faux-viper and some other goodies.

 

The new kickstarter they just finished has tie fighters and shuttles 

 

I highly recommend the company's stls. They have all come out well though their instructions need some serious rework.

  • Like 5

Share this post


Link to post
Share on other sites
19 hours ago, Kangaroorex said:

2nd Dynasty's starfighters thats 2 of the 3 cores the kit makes a number of clones like the Awing and X wing here.  The kit will also make a couple of versions of faux-viper and some other goodies.

 

The new kickstarter they just finished has tie fighters and shuttles 

 

I highly recommend the company's stls. They have all come out well though their instructions need some serious rework.

Imperial shuttles? Crud this is the first KS of theirs I passed on.

  • Like 1

Share this post


Link to post
Share on other sites

Finally had a problem with part of the Black Scrolls Prison - getting the largest room off of the build plate.

 

One quick e-mail later, the answer was... ... ... a rubber mallet.

 

*TAP!* And done. ^_^

 

I would never have though of using straight up brute force - but it worked perfectly.

 

Sometimes the answer really is 'use a bigger hammer'.

 

The Auld Grump

  • Like 1
  • Haha 8

Share this post


Link to post
Share on other sites

Just another little fun piece from the legendary dragons kickstarter

 

Meet the Puggagon. Half dragon half pug all cuteness and horror (don't think about it too hard...) printed on a press mk2.5 with silk PLA filament and .1 layer thickness20201107_154259.thumb.jpg.49496d80ccfc48ebb14714dd7f8fcf58.jpg20201107_154325.thumb.jpg.20e67e89daffe0ca4f970959340ab738.jpg

  • Like 5

Share this post


Link to post
Share on other sites
On 10/28/2020 at 9:12 PM, Kangaroorex said:

I think this plane did not land so well.

 

3d printed using a prusa 

 

20201028_220953.thumb.jpg.16071682faa630c63e7d14b96d6e0058.jpg

Nice to see a print of this and painted up nicely. 

  • Like 3

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...