Jump to content

Recommended Posts

Ok, so next week I'm gonna be replacing the LCD in my printer finally, but I'm also gonna replace the noisy fan on the very bottom of the printer. I finally found a good shot of the guts from the bottom:

 

sQjWyP5.jpg

 

Now the fan I ordered a few months ago is definitely not the one I need as it's one of the filter fans. So I'm gonna have to order a fan this week. That is why I'm posting here. What fan is good for this?

 

I've read where someone has modded theirs to run a 120mm fan, I just wanna do a direct replacement of it. One caution I have is the connections. Does the fan just clip into one of the white connectors or is it one that the wires go into the posts that screw down (like on a Ender 3)?

 

Funny how now I find this site vs trying to find anything these past few months:

 

3d967e5d28dd69948b32f5bf5c44a8a4.jpg

(note the fan wire, it clips into one of the white connectors (yeah!!)

Any help will be appreciated for this.

  • Like 1
Link to post
Share on other sites

I've yet to look inside my printer, much less yours, so I'm just guessing here.

 

I can't really judge visually, but google tells me that model is an 80mm fan. Have you tried searching a computer parts site for an 80mm case fan? It will give you a decibel rating on the site.  For example, this fan that popped up on newegg says its 20.9db.

 

35-103-025-02.jpg

  • Like 2
Link to post
Share on other sites

One upside. The photons use 12v fans. If you measure the full width of the housing in mm, you should be able to buy just about any electronics cooling fan in that size (for ex, if it's 80mm then you would need a 80x80 12v fan)

Noctua fans are well known for very quiet operation while maintaining very high volumes of air moved, and are popular replacement fans for ender 3s and other i3 clones, though on those you have to take care as they use 24 volts so some kind of regulator is needed.

 

  • Like 2
Link to post
Share on other sites

I have an EPAX X1, which has essentially the same internals as the Photon.  I replaced both the LED cooling fan and exhaust fan with Noctua fans and have not had any issues.  The only time I notice the printer running is when the build plate lowers into the vat at the beginning of the print, and when the build plate returns to the top when the print is finished.  In both cases this is the z-axis motor and the fans make next to zero noise.

  • Like 2
Link to post
Share on other sites

So would this one work then?

 

Noctua NF-R8 redux-1800 PWM, High Performance Cooling Fan, 4-Pin, 1800 RPM (80mm, Grey)

 

Item Dimensions LxWxH 3.15 x 0.98 x 3.15 inches
Brand Noctua
Power Connector Type 4-Pin
Cooling Method Fan
Noise Level 17.1 dB

About this item

  • High performance cooling fan, 80x80x25mm, 12V, 4-pin PWM, max. 1800 RPM, max. 17.1 dB(A), >150,000 h MTTF
  • Renowned NF-R8 high-end 80x25mm 12V fan, more than 100 awards and recommendations from international computer hardware websites and magazines, hundreds of thousands of satisfied users
  • Highly optimised low-noise design with outstanding quietness of operation, static pressure and airflow (CFM), ideal for chassis ventilation, cooling fan replacement for NAS and other devices, etc.
  • 1800rpm 4-pin PWM version with excellent balance of performance and quietness, supports automatic motherboard speed control (powerful airflow when required, virtually silent at idle)
  • Streamlined redux edition: proven Noctua quality at an attractive price point, wide range of optional accessories (anti-vibration mounts, S-ATA adaptors, y-splitters, extension cables, etc.)
Link to post
Share on other sites

Probably.  The critical specs are the dimensions and the voltage.

 

In my case, the Noctua fan was 10mm thicker that the stock fan, but I plenty of room after I replaced the LED array.

 

Also, you will probably need to clip off the stock connector from the Noctua fan and wire it onto the connector that fits your printers main board.   My connector was a standard screw-down block, so all I needed was wire strippers and a screw driver.

 

Edit:  You'll probably only need the red and black wires.  Yellow is for voltage control to vary to RPM of the motor.  In this application you only need on and off.  In my case, the main board connector also had no place to connect the yellow wire.

Edited by Clearman
Link to post
Share on other sites
1 hour ago, Auberon said:

They sell case fans with different types of connectors.  It's worth looking to see what you have. i.e. don't buy the 4-pin and have to splice when you could have just purchased a 3-pin.

 

Yah, I went looking afterwards & a found one with a 2 pin connector. Since that appears to be the one that is correct for board. It's not a Nocturna brand, but hey if it works for my machine, then I'll take it.

 

ee3fed88b1efdadb45c554688e127ab3.jpg

 

I'm not going to mod or doing anything out of the box on this one. I just want to change out a noisy fan (& old LCD) at the same time. I hope I don't need to tear down like this just to replace the fan. I did find it funny that there is a filament printed part inside:

 

ba40d310bd9e98799b05b0383b94428c.jpg

 

This is the housing where the lights are located at. :lol:

 

I'm kinda looking forward to doing this as it'll get me familiar with the guts of my printer but it's been awhile since I've taken a electronic apart & fiddled around inside it.

Link to post
Share on other sites
11 hours ago, Clearman said:

Yellow is for voltage control to vary to RPM of the motor.  In this application you only need on and off.  In my case, the main board connector also had no place to connect the yellow wire.

 

On the 3 pin, I thought the yellow wire was to report back speed to the motherboard so you could see how fast the fan was actually spinning?

  • Like 1
Link to post
Share on other sites
29 minutes ago, Cygnwulf said:

 

On the 3 pin, I thought the yellow wire was to report back speed to the motherboard so you could see how fast the fan was actually spinning?

 

Yeah, that is what I was trying to say.  Yours is more correct phrasing.

 

In any case, my motherboard didn't need it, so I just taped it down so it wouldn't touch anything it shouldn't.

1 hour ago, haldir said:

I did find it funny that there is a filament printed part inside:

 

1) Buy 3D printer.

2) Use 3D printer to print another 3D printer

3) Return first printer

4) Profit.

  • Like 2
Link to post
Share on other sites
1 minute ago, Clearman said:

 

Yeah, that is what I was trying to say.  Yours is more correct phrasing.

 

In any case, my motherboard didn't need it, so I just taped it down so it wouldn't touch anything it shouldn't.

 

This is something I'm trying to avoid. The machine works, just a loud squealing fan when the plate goes down to print. Why I'm just trying to do a direct replacement. I did pick up a file off thingiverse for brackets to make it useable for a 120mm, I was thinking maybe after I'm familiar with the innards of the machine, I'll upgrade to that. Thou, you can print the bracket on a resin printer, I think that is something more suited for FDM printing. (Anther thing I need to do while on vacation, fix that damn belt on the Ender 6...ughhh it never ends...)

  • Like 2
Link to post
Share on other sites
15 minutes ago, haldir said:

This is something I'm trying to avoid.

 

I do as well, but my research indicated the model fan I used was highly recommended for this application.  

  • Like 2
Link to post
Share on other sites

I ordered my fan replacement this morning (I should have it on Monday):

 

Item Dimensions LxWxH 3.15 x 3.15 x 0.98 inches
Brand GDSTIME
Power Connector Type 2-Pin
Voltage 12 Volts (DC)
Wattage 4.2 watts
Cooling Method Air
Compatible Devices Desktop
Noise Level 43 dB
Material Polybutylene Terephthalate
Maximum Rotational Speed 4500 RPM
 

About this item

  • Dimension of outer the frame is 80mm(L) x 80mm(W) x 25mm(H) / The size of fan in inch is 3.15in(L) x 3.15in(W) x 1in(H); The center to center distance beween the mountiong holes is 71.5mm/2.81in.
  • Operating Voltage Range:5.5V to 13.8V. (overtake to 13.8V, it can also work. but not safe, and seriously affects lifespan of fan.); Start up voltage is 3.9V.
  • Rated Current: 0.35Amp; Speed: 4500RPM ; Air flow: 59CFM ; Noise: 43dBA
  • Connector: XH2.54-2Pin; Lead wire: UL Type (+): Red wire ; (-): Black wire. This is a two wire cooling fan; Bearing Type: Dual Ball Bearings ; Life: working up to 50000h at 25 degrees.
  • Package include: 1 x 80mm cooling fan; 1x 80mm metal grill; 4*M4x35mm screws & nuts( The metal grill is separate with fan and it is mounted by screws.)
 
More then twice the noise level of the Noctura, but this one requires no fiddling with wires + is correct for the slot it'll go into.
  • Like 3
Link to post
Share on other sites

In the word of King Theodin

 

"And so it begins."

 

Started my fan & lcd changeover today. Following the above site/pics for screw removal,  I placed the screws on sheets of post it notepaper (labeled where they came out of as they are different) 

 

16155925140542386689860647677617.jpg

 

Bottom cover is off. If I ever go to a 120mm I'd have mod this.

16155925834402873428111348107564.jpg

 

Now if I do go with a 120 in the future,  I think I could do it without much fuss. Are those holes in the heatsink, mounting holes? Note one is under the existing fan in the picture. There is also a set on the first rib directly above that one.

16155926836048264272536832704567.jpg

 

This is where I was before I decided to document this.

 

To be continued.....

 

 

(posts merged here)

 

More dismantling

Standoffs & mounting screws & the actual fan!

16155931129846712666279744456334.jpg

 

Also clearer pic of the heatsink & those holes. Screws do fit them :winkthumbs:

 

 

16155932085001703747818261574152.jpg

 

Also pic of the mainboard just for the hell of it. Notice the onboard ethernet box/port above the USB connection?? Hmmm. The flat ribbon cable is the front LCD screen connection. I do believe the LCD board is to the left of this picture. Also notice the small fan under the USB port? That is 1 of 2 that flows air out of the print area. (the ones with the charcoal filters) these things are tiny!! That official Anycubic fan I got off Big River is bigger then these. I have no idea what the fan even goes to, maybe one of their FDM printer perhaps??

16155932869658809799880923658985.jpg

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By MoonglowMinis
      How do you make an octopus laugh?  You give him ten tickles!

      Wanted to show off this little octopus that I sculpted from some leftover green stuff.  I don't have much experience with sculpting other than a few simple embellishments on minis and a couple of snake swarms I made once.  Wanted to try something relatively simple and figured an octopus would be pretty forgiving.
       
      You can see more about how I made this guy and more of my nautical minis in my Dark Tide WIP thread HERE.

       
      I sculpted and painted this guy in two evenings and am happy with hos cute it turned out.  It's not the most accurate, but I'm proud of it.  It definitely has given me greater confidence in my ability to make something out of nothing.
       
      More Photos Beneath the Spoiler:
       
    • By MoonglowMinis
      So for awhile now I've had this goal, nay, this desire, nay, this primal compulsion to build a boat.  It is not enough to have hand drawn maps, or 2D terrain tiles.  I need a fully functioning 3D boat!  Well, maybe not fully functioning.  But I want to build a cool boat!
       
      I've been working on a nautical campaign full of swashbuckling, sailing, and sea monsters for a few years now.  It's my White Whale project.  Always just on the horizon.  It'll happen some day, but in the meantime, I have a million small projects to complete and extend the chase.  One of which is my desire to build a few different sized ships to enliven any possible naval combat.
       
      I actually attempted this about two years ago, just winging it and making some measurements and throwing them at some craft supplies.  I wanted a cheap option that wasn't too difficult to repeat that way I wouldn't be discouraged from making multiple ships.  So I limited it to cheap crafting materials like foamcore, wooden dials, popsicle sticks, and thumbtacks.  And the result wasn't  bad.  Especially for my first attempt at any kind of terrain building.


      It actually turned out rather nice!  To my surprise.  But I got hung up on mast and sail designs and never finished.

      The wood on the deck had 2x1in grid carved into it for easier D&D use.

      and the figurehead was designed to be modular.

      However, overtime the boat collected dust and little scratches.  I should have given it a coat of mod podge or sealant of some kind, but never did.  And eventually it had an unfortunate run in with an injured owl that we took in for a night.

      Here's the little devil himself.
       
      Anyways, I put this project on the back burner for long enough and feel inspired to dive back in.  Especially with a certain Bones ship on the Horizon that I'm still on the fence about getting.  I was doing some browsing on the web and recently found this wonderful little blog complete with loose instructions and a plan from a now defunct wargamming site.  The blog creator had found the old plan and adapted it to build something using most of the same materials I have already stockpiled. 


      There's a few choices that I like better than my first attempt so I think I'm going to use this as some inspiration as I give this boat thing another go.

      My hold up now is still those darn masts.  The original plan above used wood and required drilling out holes for the masts.  The blogger use foam for his ship and found random bits of tubing to house his masts.  I could try to find something random like that, but I was hoping to find something simpler for easy repetition.  And I would also like to keep the masts loose so they can be removed for easy storage, or to swap out the sails.  Any thoughts?

      Any resources, tips, recommendations are very welcome!  I'll post back here with any updates.

    • By Nook
      Greetings all!
      I had a fun idea for a mini that I need for an upcoming game, so I decided to DIY it. So this will be my
      DIY Ochre Jellies 
       
      I’m using white gorilla glue, the kind that foams up, and a bent safety pin. As it begins to dry I moved the “blob” up along the pin to gain some vertical height. The white will be an ok under coating, and I’ll paint it up tomorrow once it finishes drying. I’ll snip the end of the safety pin off before painting too. 
    • By Disciple of Sakura
      http://kck.st/2mr5iKg
       
      An enormous wooden d20 capable of holding up to a pound of dice. I haven't got one of these yet, but I have gotten some other items from Munchkin Metropolis, and was really satisfied with how quickly the items were produced and arrived. Great quality, too.
    • By lexomatic
      I'm not really sure when I'll get to these, but I found a bunch of cheap sheets that I'm going to diy into mats for wargaming. As it is, they're fine (I got green, blue, and brown, and passed on a grey) . But I might sponge on some various paints for waves/ ice (double sided blue sheet) and various greens for the green sheet.
  • Who's Online   18 Members, 1 Anonymous, 41 Guests (See full list)

×
×
  • Create New...